Draper Patriot Motorized Flag 500101 Manual de instruções - Página 5

Procurar online ou descarregar pdf Manual de instruções para Mobiliário de interior Draper Patriot Motorized Flag 500101. Draper Patriot Motorized Flag 500101 8 páginas.

Imprimir página

Patriot Motorized Flag

Section 4 - Electrical Connections

1. Motorized Flag operates on 110-120V, 60 Hz., 2.3 amp current draw.

2. Junction box is located just above the bottom access panel at the left end of the Motorized Flag.

3. Open the access panel/trap door for access to the junction box cover.

opening and closing instructions below)

4. Remove two

hex head screws that secure the cover to the junction box to expose the red, black,

(2)

and white pigtail leads and the green ground wire per wiring diagram on at right.

5. Motorized Flag ships with internal wiring complete and control switch

Wire to connect Motorized Flag to switch

installer. Connections should be made in accordance with wiring diagram

comply with national and local electrical codes.

6. All operating switches should be "off" before power is connected.

Section 5 - Limit Adjustments

Please Note: Flag limits are

factory set for optimum

performance of the flag. Any

adjustment of these limits could

void the warranty. Please check

with Draper prior to resetting flag

limits.

Please Note: If flag is "Right Hand

Motor," the WHITE/DOWN

and

(I)

YELLOW/UP

limit screws are

(II)

reversed

(Fig. 11)

CAUTION:

- Be sure all switches are in "off"

position before adjusting limit

switches.

- Be prepared to shut off manually

while testing.

and switch

to power supply should be furnished by

(es)

Please Note: Do not wire motors in parallel.

Figure 10

DOWN Limit (I)

DOWN Limit

Clockwise

Clockwise decreases

decreases

down travel.

UP Limit (II)

UP Limit

(II)

Counterclockwise

increases up travel.

- Flag may be damaged by

lowering it too far and

exposing roller.

- Motor must be installed so that

limit switches are pointed down.

(See bottom access panel/trap door

fully boxed.

(es)

, and wiring should

(at right)

Section 5.1 - Standard Motors Limit Adjustments

(I)

Section 5.1.1 - "Down" Limit Adjustment

To Reduce Flag Drop:

1. Raise flag surface approximately 1'

and turn off.

2. Turn DOWN

limit screw clockwise

(I)

3. Test by lowering flag. Repeat steps 1 & 2 until desired position

is reached.

To Increase Flag Drop:

1. Lower flag to down limit.

2. With down switch on, turn DOWN

(3 screw turns = 1/2 roller revolution)

3. Test by raising flag approximately 1'

down limit.

4. Repeat steps 2 and 3 until desired position reached.

Section 5.1.2 - "Up" Limit Adjustment

If Flag Raises Too High:

1. Lower flag surface approx. 1'

2. Turn UP

limit screw clockwise

(II)

3. Test by advancing flag up.

4. Repeat steps 1 through 3 until desired position is reached.

If Flag Needs to Raise Higher:

1. Lower flag surface approx. 1'

2. With UP switch on, turn UP

(3 screw turns = 1/2 roller revolution)

3. Repeat steps 1 and 2 until desired position is reached.

CAUTION: DO NOT allow dowel to wrap over roller when operating flag! This

could damage flag.

110-120V MOTOR

STANDARD

Single Station Control

Internal Screen Wiring

White (Common)

Black (Down)

Red (Up)

Green (Ground)

Dashed wiring

by electrician.

Single gang box by others.

Control

Min. 4" x 2 ⁄ " x 1 ⁄ " deep.

switch

(102mm x 54mm x 48mm)

Blue

Red

Black

* Wiring diagram is for

Patriot with motor on

audience left

and fabric unrolling

Location of key

from the back of the

operated on-off

switch if furnished.

roller

To 110-120V Line

(Fig. 10)

(requires 5/32" (4 mm) Hex key)

above desired setting

(30 cm)

(3 screw turns = 1/2 roller revolution)

limit screw counterclockwise

(I)

to increase drop.

then down to new

(30 cm)

below desired setting and turn off.

(30 cm)

(3 screw turns = 1/2 roller revolution).

below desired setting and turn off.

(30 cm)

limit screw counterclockwise

(II)

page 5 of 8

(standard)