Allied Motion TCI V1K Kit Manual de instalação

Procurar online ou descarregar pdf Manual de instalação para Sistemas de filtragem de água Allied Motion TCI V1K Kit. Allied Motion TCI V1K Kit 2 páginas.

Imprimir página

General Safety Instructions

Warning

Be sure to read, understand, and follow all safety

instructions.

Warning

Only qualified electricians should carry out all

electrical installation and maintenance work on

V1K drive output filters.

Warning

All wiring must be in accordance with the National

Electrical Code (NEC) and/or any other codes that

apply to the installation site.

Warning

Disconnect all power before working on the

equipment. Do not attempt any work on a powered

V1K output filter.

Warning

The V1K, VFD, motor, and other connected

equipment must be properly grounded.

The VFD terminals and connected cables are at a

Warning

dangerously high voltage when power is applied to

the VFD, regardless of motor operation.

Installation Checklist

• Access V1K installation drawings on the TCI website

for unit dimensions, mounting hole pattern, mounting

orientation, wire locations, unit weights, and other

unit specific installation notes.

https://transcoil.com/

products/v1k-motor-protection-filter/

• Ensure installation location is not exposed to corrosive

liquids or gases, explosive or combustible gases or

dust, excessive airborne dirt and dust, or excessive

vibration.

• Select mounting area that allows adequate cooling air

and maintenance access.

• Ensure all wiring conforms to requirements of the

National Electric Code (NEC) and\or other applicable

electrical codes.

• Ground V1K output filter to a dedicated system

ground to ensure safety and filter performance. Use

properly sized grounding conductor.

• Wire output power terminals of the VFD to the input

terminals of the V1K: U, V, & W.

• Wire the output power terminals of the V1K, T1, T2, &

T3 to the motor power connections.

• Ensure VFD is set for operating modes and ranges

that are compatible with the V1K.

• Check entire system thoroughly before energizing and

operating any equipment.

When you receive the unit, immediately inspect the

shipping container and report any damage to the

shipping carrier who delivered the unit.

Field Wiring Connection Terminals

Compression type terminals are available for all line wiring

connections. The wire size capacity ranges and tightening

torque for the reactor power terminals are listed in the

table.

Reactor Terminal Block/

Optional Lug Kit Terminals

V1K Kit

Current

Part Num.

Rating

Wire Size

V1K2A0K

12 - 14 AWG

V1K3A0K

12 - 14 AWG

V1K4A0K

12 - 14 AWG

V1K6A0K

12 - 14 AWG

V1K8A0K

12 - 14 AWG

V1K12A0K

12 - 14 AWG

V1K16A0K

4 - 12 AWG

V1K18A0K

4 - 12 AWG

V1K21A0K

4 - 12 AWG

V1K25A0K

4 - 8 AWG

V1K27A0K

4 - 8 AWG

V1K35A0K

6 - 8 AWG

V1K45A0K

6 AWG

V1K55A0K

1 - 4 AWG

V1K80A0K

1 - 3 AWG

V1K110A0K 110

2/0 - 1/0 AWG

V1K130A0K 130

2/0 AWG

V1K160A0K 160

250 kcmil - 3/0 AWG

V1K200A0K 200

(2) 2/0 - 1 AWG

V1K250A0K 250

(2) 2/0 AWG

V1K305A0K 305 (2) 350 kcmil - 3/0 AWG

V1K362A0K 362 (2) 350 kcmil - 4/0 AWG

V1K420A0K 420

(2) 600 - 300 kcmil

V1K480A0K 480

(2) 600 - 350 kcmil

V1K600A0K 600

(2) 600 - 500 kcmil

V1K750A0K 750

(3) 600 - 400 kcmil

All electrical connections must be re-torqued annually.

See www.transcoil.com for component drawings and dimensions.

Please contact TCI Technical Support or your TCI distributor for

application information regarding the use of V1K output filters on

the output side of the VFD.

TCI, LLC

W132 N10611 Grant Drive,

Germantown, Wisconsin 53022

800-824-8282 | www.transcoil.com

Board

Lug

Part

Kit

Torque

Num.

Installation Guide

(lb-in)

25009

N/A

25009

N/A

25009

N/A

25009

N/A

Product Specifications

25009

N/A

• Current Rating: 2 - 750 Amps, 208 V - 600 V, .75 - 600 HP

25009

N/A

• UL Listed

25009

N/A

• Efficiency > 98%

25009

N/A

• Insulation Rating: 600V Class

25009

N/A

• Insulation Class: Class H (180°C or better)

25009

N/A

• Maximum Altitude: 2000 m (6,000 ft) Derating necessary

25009

N/A

above 2000 m

25011

N/A

• Lead Length: up to 1,000 ft (Specific applications could

25011

N/A

reach longer lead lengths.)

25011

N/A

• Ambient Temp: Min -25°C, Max 40°C

25011

N/A

• For use with three phase VFDs operating at 2 kHz - 4 kHz

25011 SLK10

PWM carrier frequency and with a maximum motor cable

25011 SLK10

size necessary to achieve a 5% voltage drop at 1,000 ft.

375

25012 SLK21

• Optional thermal switch electrical rating: 120 V/6 A

25012 SLK22

• Switch opens on temperature rise

25012 SLK22

• 2 A to 12 A standard 195°C trip

375

25012 SLK13

• 2 A to 12 A EX version 160°C trip

375

25012 SLK13

• 16 A to 110 A 160°C trip

500

25012 SLK14

500

25012 SLK14

500

25012 SLK14

500

25012 SLK16

Revision 1.0

V1K Kit

Wiring Diagram

TCI, LLC

W132 N10611 Grant Drive,

Germantown, Wisconsin 53022

800-824-8282 | www.transcoil.com

Part # 31259

06/06/2022