Digiplex DGP2-PS17 Manual rápido

Procurar online ou descarregar pdf Manual rápido para Fonte de alimentação Digiplex DGP2-PS17. Digiplex DGP2-PS17 2 páginas.

Imprimir página

Power Supply Module V1.0

(DGP2-PS17)

Instructions

DGP2PS17-EI00

NTRODUCTION

The Power Supply Module (DGP2-PS17) is a fully supervised 1.7A switching

power supply that is connected to the communication network of the Digiplex

(DGP-48) or DigiplexNE (DGP-NE96) control panel.

NSTALLATION

The DGP2-PS17 is connected to the control panel's communication

network in a star and/or daisy chain configuration. This 4-wire

communication network provides power and two-way communication

between the control panel and all modules connected to it. Connect the four

terminals labeled red, black, green and yellow of the DGP2-PS17 to the

corresponding terminals on the control panel as shown in Figure 1 (refer to

reverse side). Connect the 5A PGM output of the DGP2-PS17 as shown in

Figure 1, Inset 2 (refer to reverse side).

ROGRAMMING

ETHOD

To program the DGP2-PS17, you must enter the "Module Programming

Mode" using any keypad in the system:

1) Press and hold the [0] key.

2) Key in the [

INSTALLER CODE

3) Key in section [953] (DGP-48) / [4003] (DGP-NE96).

4) Key in the DGP2-PS17's 8-digit [

5) Key in the 3-digit [

] you wish to program.

SECTION

6) Turn the desired option ON/OFF or key in the required data.

Please note that the serial number is located on the DGP2-PS17's PC

board. The DGP2-PS17 can also be programmed using the control panel's

Module Broadcast feature as well as through the WinLoad Software (V2.0

or higher). Refer to the Digiplex or DigiplexNE Reference & Installation

Manual for more information on the Module Broadcast feature and to

WinLoad's Online Help for information on programming with WinLoad.

Tamper Recognition

The DGP2-PS17 does not come equipped with a tamper switch. If your

installation requires tamper recognition, enable this feature and connect a

tamper switch as shown in Figure 1, Inset 1 (refer to reverse side). When a

tamper is detected on the module, it will send a tamper report to the control

panel via the communication network. Default: Option [1] is OFF.

Battery Charging Current

Turning option [2] ON will set the battery charging current at 700mA.

Turning option [2] OFF will set the battery charging current at 350mA. A

battery charging current of 350mA will require more time to charge the

battery compared to 700mA but will consume less power from the module

itself. Default: Option [2] is OFF.

SERIAL NUMBER

Section [001] - Option [1]

Section [001] - Option [2]

PGM Deactivation Option

When the PGM Activation Event occurs, this option determines when the

PGM will return to its normal state (deactivate). When option [3] is ON, the

PGM will deactivate when the PGM Timer programmed in section [003] has

elapsed. When option [3] is OFF, the PGM will deactivate when the PGM

Deactivation Event programmed in sections [008] to [011] occurs.

Default: Option [3] is OFF.

PGM Base Time Selection

If the PGM Deactivation Option (section [001] option [3]) is set to follow the

PGM Timer, you must define whether the PGM Timer programmed in

section [003] is in minutes or seconds. If option [4] is ON, the PGM Timer

will be in minutes. If option [4] is OFF, the PGM Timer will be in seconds.

Default: Option [4] is OFF.

PGM Timer

If the PGM Deactivation Option (section [001] option [3]) is set to follow the

PGM Timer, the value programmed in section [003] represents how long

the PGM will remain in its opposite state after being activated. To program

the timer, enter a 3-digit decimal value (001-255) into section [003], where

this value is multiplied by the PGM Base Time Selection (section [001]

option [4]) of 1 second or 1 minute. Default: 005.

PGM Activation Event

The PGM Activation Event determines which event will activate the DGP2-

PS17's on-board PGM output. The Event Group specifies the event, the

Feature Group identifies the source, and the Start # and End # sets the

range within the Feature Group. Use the PGM Programming Table in the

Digiplex/DigiplexNE Modules Programming Guide to program the DGP2-

PS17 PGM Activation Event. Enter the sections that correspond to the

Event Group, Feature Group, Start # and End # of the PGM and enter the

required data.

Event Group

Feature Group

PGM

[004]

Only Event Groups 000 to 055 can be used to program the

DGP2-PS17's PGM Activation Event.

PGM Deactivation Event

If the PGM Deactivation Option is set to follow the PGM Deactivation Event

(Section [001] option [3]), the PGM will return to its normal state when the

event programmed in sections [008] to [011] occurs. The Event Group

specifies the event, the Feature Group identifies the source, and the Start #

and End # sets the range within the Feature Group. Use the PGM

Programming Table in the Digiplex/DigiplexNE Modules Programming

Guide to program the DGP2-PS17 PGM Deactivation Event. Enter the

sections that correspond to the Event Group, Feature Group, Start # and

End # of the PGM and enter the required data.

Event Group

Feature Group

PGM

[008]

Only Event Groups 000 to 055 can be used to program the

DGP2-PS17's PGM Deactivation Event.

Section [001] - Option [3]

Section [001] - Option [4]

Section [003]

Sections [004] to [007]

Start #

[005]

[006]

Sections [008] to [011]

Start #

[009]

[010]

End #

[007]

End #

[011]