Whirlpool Cabrio,- WED7300X Manual de utilização e cuidados - Página 17

Imprimir página

Whirlpool Cabrio,- WED7300X Manual de utilização e cuidados

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.whirlpool.com/help

If you experience

Washer not performing as expected (cont.)

Incorrect dispenser

operation

Error Code Appears in Display

oL (overloaded)

appears in display

uL (unbalanced load)

appears in display

LF (too long to fill)

appears in display

Ld (too long to drain

water ) appears in

display

HC (Hot and Cold

hoses reversed)

appears in display

Sd (Excess suds)

appears in display

dL (Lid cannot lock)

appears in display

lid (Lid opened)

appears in display

dU (Lid cannot unlock)

appears in display

F## code (F-type

error code) appears

in display

for assistance and to possibly avoid a service call.

Possible Causes

Clogged dispensers or laundry

products dispensing too soon.

Liquid chlorine bleach not

used in dispenser.

Load too large.

Load not balanced. The washer is

running a load-balance correction

routine.

Washer taking too long to fill.

Drain extends more than

4.5" (114 mm) into standpipe.

Washer taking too long to drain

water. Drain extends more than

4.5" (114 mm) into standpipe.

Hot and cold inlet hoses have been

installed incorrectly.

Excessive suds in washer. Washer is

running a suds reduction routine.

An item in the load may be keeping

the lid from locking.

Washer lid left open.

Objects on washer lid prevent it from

unlocking.

System error code.

Do not overfill dispenser. Overfilling causes immediate dispensing.

Always select Fabric Softener option to assure proper dispensing.

Load dispensers before starting a cycle.

It is normal for small amounts of water to be remain in dispenser at

the end of the cycle.

Homes with low water pressure may result in residual powder in the

dispenser. To avoid, select a warmer wash temperature if possible,

depending on your load.

Use only liquid chlorine bleach in the Bleach dispenser.

If the washer is overloaded, it will drain any water and detergent

in the washer. Remove several items and add HE detergent

Close lid and press START/PAUSE.

Allow the machine to continue. If the dial is flashing and the

machine has stopped, redistribute the load, close the lid, and

press START/PAUSE.

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening. See "Installation Instructions".

Check plumbing for correct drain hose installation. Use drain

hose form and attach securely to drainpipe or tub. Do not tape

over drain opening.

Lower drain hose if the end is higher than 96" (2.4 m) above

the floor. Remove any clogs from drain hose. See "Installation

Instructions".

This code will appear at the end of the wash cycle to indicate

that cold water hose is connected to the hot water inlet and hot

water hose is connected to the cold water inlet.

Allow the machine to continue. Use only HE detergent.

Always measure detergent, and base detergent quantity on

load size. Follow detergent manufacturer's instructions. If the

dial is flashing, reselect your desired cycle using a cold wash

temperature, and press START/PAUSE. Do not add detergent.

Make sure that the washer is not overloaded, and make sure no

items are above the top of the stainless steel basket.

Close the lid to clear the display. If the lid is left open for more

than 10 minutes, the cycle will reset and water in the washer

will drain.

Remove objects, such as a basket of laundry, from the top of

the washer.

Press START/PAUSE once to clear the code. Then press

START/PAUSE again to restart washer. If code appears again,

call for service.

Solution