Emerald Planet EP-HW-240-R1 Руководство пользователя - Страница 3
Просмотреть онлайн или скачать pdf Руководство пользователя для Дымовая сигнализация Emerald Planet EP-HW-240-R1. Emerald Planet EP-HW-240-R1 6 страниц.
Также для Emerald Planet EP-HW-240-R1: Инструкция по установке (4 страниц)
Печатать страницу
OPERATION
TESTING
Test the unit to ensure proper operation by pressing the test
button, this will sound the alarm if the electronic circuitry, horn,
and battery are working. If no alarm sounds, please refer to the
"Troubleshooting" section for solution.
DO NOT USE AN OPEN FLAME TO TEST YOUR ALARM, YOU
COULD DAMAGE THE ALARM OR IGNITE COMBUSTIBLE
MATERIALS AND START A FIRE.
CAUTION: DUE TO THE LOUDNESS (85 DECIBELS) OF THE
ALARM, ALWAYS STAND AT ARMS-LENGTH AWAY FROM
THE UNIT WHEN TESTING. TEST THE ALARM WEEKLY TO
ENSURE PROPER OPERATION. ERRATIC OR LOW SOUND
COMING FROM YOUR ALARM MAY INDICATE A DEFECTIVE
ALARM, PLEASE REFER TO "TROUBLESHOOTING" SECTION
FOR SOLUTION.
NOTE: WEEKLY TESTING IS REQUIRED.
LED INDICATORS
Green LED illuminated: indicates that the alarm is receiving AC
power. This alarm is also equipped with a Red LED indicator,
with two modes of operation.
Red LED-Flashing once every 32 seconds: indicates that the
smoke alarm device is operating properly.
Red LED-Flashing when the test button is pressed, or when the
smoke alarm device senses particles of combustion and goes
into alarm (constant pulsating sound), the red LED will flash
once per second. The flashing LED and pulsating alarm will
continue until the air is cleared or test button is released.
Red LED-Alarm silencer (Hush mode) indication: The red LED
will flash once every 8 seconds, indicating the smoke alarm
device is in the alarm silence (Hush) mode.
Low battery indication - An intermittent "chirp" with red
LED flashes once every 32 seconds: indicates that the smoke
alarm device is low on battery, you may press the test button
to pause the alarm for 10 hours, but it will reset automatically
after 10 hours.
Fault indication - The alarm chirp occurs every 40 seconds.
NOTE: WHEN THE UNIT CHIRPS ONCE EVERY 40 SECONDS,
YOU CAN PRESS THE TEST BUTTON TO TEMPORARILY
PAUSE THIS WARNING TONE FOR 10 HOURS. IT CAN STILL
NORMALLY DETECT SMOKE DURING THIS PERIOD, IT ONLY
REMOVES NUISANCE WARNING TONE. YOU CAN REFER TO
"TROUBLESHOOTING" FOR SOLUTION. IF THERE ARE STILL
FAILURES, YOU MUST REPLACE IT WITH A NEW ALARM AT
ONCE OR CONTACT YOUR RETAILER DURING WARRANTY
PERIOD.
ALARM SILENCE (HUSH MODE)
To silence an alarm, push the test button, it will pause the
alarm for approx. 8 minutes. The red LED will flash once every
8 seconds, it indicates the smoke alarm is running in "silence
mode". Smoke alarms are designed to minimise nuisance
alarms. Combustion particles from cooking may set off the
alarm if the alarm is located close to the cooking area. Large
quantities of combustible particles are generated from spills or
when grilling/frying. Using the fan on a range hood that vents
to outside (non-recirculating type) will also help remove these
combustible particles from the kitchen. The alarm silence (test
button) is extremely useful in a kitchen area or other areas
prone to nuisance alarms. The silence feature is to be used only
when a known alarm condition, such as smoke from cooking
activates the alarm.
The smoke alarm will automatically reset after approximately
10 minutes, if after this period, particles of combustion are still
present, the alarm will sound again. The alarm silencer (silence
mode) can be repeatedly until the air has been cleared of the
condition causing the alarm.
CAUTION: BEFORE SILENCING THE ALARM IDENTIFY THE
SOURCE OF SMOKE AND ENSURE THERE IS NO RISK OF
FIRE.
EMERALD PLANET HEAD OFFICE - SYDNEY Unit 2 / 29 Mitchell Road, Brookvale NSW 2100 Australia P 02 9466 6000
NOTE: DENSE SMOKE WILL OVERRIDE THE SILENCE MODE
AND THE ALARM WILL SOUND A CONTINUOUS ALARM
AGAIN.
DANGER: IF THE ALARM SOUNDS, AND IT IS NOT BEING
TESTED, IT MEANS THE UNIT IS DETECTING SMOKE AND
REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION.
MAINTENANCE & CLEANING
The alarm should be cleaned at least once a year.
• To clean your alarm, remove it from its bracket on ceiling,
you can clean it by using compressed air or a vacuum
cleaner hose with a soft brush attachment. Blow or vacuum
around the perimeter of the alarm to remove dust and dirt
and debris. The outside of the alarm can be wiped with a
damp cloth but you should avoid using a wet cloth in order
to avoid water entering the interior of alarm.
• After cleaning, reinstall it and test it by pressing the Test
button. The alarm should be replaced if cleaning can't
restore the alarm to normal operation.
• This alarm has a low battery monitor which will cause the
alarm to "chirp" approx. every 40 seconds and the red LED
flash once at the same time for a minimum of thirty days
when the battery gets low.
If there is a defective battery or other failures, you can refer
to "Troubleshooting" for solution, or deactivate this alarm
to stop nuisance alarm which is caused by a failure of their
function. If there are still failures during warranty period, you
can return to your retailer.
• Don't paint the unit. Paint will seal the vents and interfere
with the sensor's ability to detect smoke.
NOTE:
1. REGULAR WEEKLY TESTING IS RECOMMENDED.
2. ALARMS MUST BE REACTIVATED BEFORE USE IF
THEY ARE DEACTIVATED.
REPLACING THE ALARM
It is recommended this alarm should be replaced ten years
from the date of manufacture. This date has been provided on
the product label which is located on the back of the alarm
IMPORTANT: DO NOT ATTEMPT TO REMOVE THE COVER
TO CLEAN INSIDE. THIS WILL AFFECT WARRANTY.
REPAIR
If the alarm is not operating properly, and is still under
warranty, return it to the original place of purchase.
If the alarm is no longer under warranty, please replace it
immediately with a comparable alarm.
CAUTION: DO NOT ATTEMPT TO REPAIR THE ALARM. IT
WILL AFFECT YOUR WARRANTY.