3Doodler PRO+ Руководство пользователя - Страница 4

Просмотреть онлайн или скачать pdf Руководство пользователя для Аксессуары 3Doodler PRO+. 3Doodler PRO+ 16 страниц.

Печатать страницу

Please Doodle here:

Step 4: Learn How to Doodle in 3D

Use the 3Doodler PRO+ to transform your triangle into

pyramid!

With the triangle flat on the

page, extrude Filament onto one

corner of the triangle until you

have a small blob. Make sure

it is anchored onto the triangle

before moving to the next step.

Click the Feed Button to stop

extrusion, BUT DO NOT MOVE

THE PEN YET.

Pull the pen away. The line will

remain vertical.

Well done! You just Doodled in the air! This is a crucial

stepping stone to making all kinds of three dimensional

objects with your 3Doodler PRO+.

YouTube videos: Cube

https://www.youtube.com/watch?v=vL6gLsCYfO8

For more videos visit:

https://www.youtube.com/3Doodler

Resources for further inspiration and

guidance:

https://www.3Doodler.com/resources

1.5 in

With the pen extruding, lift the

Nozzle up off of the paper in a

straight line for 1.5 inches above

the center of the triangle.

5-6

secs

Wait a few seconds with the pen

still connected to the top of your

Filament's line.

Repeat twice from the two

remaining corners of the triangle.

Step 5: Reverse and Remove Filament

BLUE

Light

Ensure the pen's temperature

is set to ABS, and that the Blue

Light is on.

Once the Filament stops reversing, it is safe to remove it from the pen

by gently pulling on the back of the strand.

SNIP THOSE ENDS!

After removing a Filament

strand from the 3Doodler PRO+,

cut and remove the melted end

of your strand before reinserting

it into the 3Doodler PRO+ .

This will reduce blockages and

clogging issues.

ALWAYS remove strands from

the 3Doodler PRO+ when the

pen is idle.

Step 6: Unblocking Filaments

BLUE

Light

Turn the pen on and set it to

the temperature of the filament

being used.

With the nozzle removed, click

the reverse button to engage the

reverse feature.

STEP 7: Custom Mode

Note: You do not have to use custom mode.

If you do choose to use Custom Mode, please use the

recommended temperature settings on page 4. To use

custom mode, select CUS in the menu, then use the

Navigation Buttons to select your desired temperature,

and click the Enter Button. After this, you can select your

preferred speed.

Note that Custom Mode is not programmed for specific

filaments like in the pre-set temperature modes, so it is

possible that a custom setting will not produce the desired

outcome. You may need to modify the Custom Mode

settings until you achieve the results you're aiming for.

Example: If you are using PLA and set the pen to 170ºC and

speed 1, that will cause difficulty in extruding.

Example: If you are using FLEXY set to 240ºC and speed 10,

you may cause the pen to lose heat too fast and extrusion will

stop until the internal temperature can get hot enough again.

Click the Reverse Button once. The

Light will start flashing to signal

that the Filament is reversing.

Remove the nozzle using the

socket located on the end of the

nozzle storage case.

*IMPORTANT: Only remove

and replace the Nozzle with

the pen turned on and fully

heated.

Unblocking

Tool

Next, while the pen is in reverse,

insert the unblocking tool through

the nozzle-end of the pen to

push any remaining filament out

through the feed port.