Canon PIXMA MP610 Series Servis Kılavuzu - Sayfa 32
Hepsi Bir Arada Yazıcı Canon PIXMA MP610 Series için çevrimiçi göz atın veya pdf Servis Kılavuzu indirin. Canon PIXMA MP610 Series 45 sayfaları. All-in-one photo inkjet printer
Ayrıca Canon PIXMA MP610 Series için: Buradan başlayın (2 sayfalar), Tamamlayıcı Kılavuz (6 sayfalar), Broşür ve Teknik Özellikler (2 sayfalar), Hızlı Başlangıç Kılavuzu (40 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar)
Sayfayı Yazdır
- 1. Table of Contents
- 1. 1 Maintenance
- 1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer
- 1. Customer Maintenance
- 1. Special Tools
- 1. Serial Number Location
- 2. 2 List of Error Display / Indication
- 2. Operator Call Errors
- 2. Service Call Errors
- 2. Other Error Messages
- 2. Warnings
- 2. Troubleshooting by Symptom
- 3. 3 Repair
- 3. Notes on Service Part Replacement
- 3. Adjustment / Settings
- 3. Verification Items
Time(s)
0 times
0%
1 time
10%
2 times
20%
3 times
30%
4 times
40%
5 times
50%
6 times
60%
7 times
70%
8 times
80%
9 times
90%
Not valid.
10 times or more
Press the ON/OFF button to return to the ink absorber counter
setting mode.
5) Press the ON/OFF button to set the selected value to the EEPROM. Print EEPROM information to confirm that the value is
properly set to the EEPROM.
<LF / Eject correction>
After replacement of the feed roller, logic board, or platen unit in repair servicing or in refurbishment operation, perform the
adjustment to maintain the optimal print image quality.
Details: Print the LF / Eject correction pattern on a sheet of paper. Select the Pattern No. (0 to 2) in which streaks or lines
are the least noticeable, press the Stop/Reset button the same number of time(s) as the selected Pattern No., then
press the ON/OFF button. (See the flowchart below.)
Note: At the production site, the E-MIP correction, which is equivalent to the LF / Eject correction, is performed using the
special tool, and the E-MIP correction value is written to the EEPROM as the valid data.
When LF / Eject correction is performed, the LF / Eject correction values become valid instead of the E-MIP
correction value (thus, in the initial EEPROM information print, "LF = *" and "EJ = *" are printed).
1) In the LF / Eject correction mode, press the Stop/Reset button the specified number of time(s) according to the paper to be used in
LF / Eject correction listed in the table below, then press the ON/OFF button. (Set a sheet of selected paper in the rear tray.)
Time(s) (L)
1 time
HR-101
2 times
GF-500, Office Planner
3 times
HP BrightWhite
4 times
Canon Extra, STEINBEIS
- Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and
Power in green.
- If the Stop/Reset button is NOT pressed, and only the ON/OFF button is pressed, the machine remains in the
LF / Eject correction mode.
- If the Stop/Reset button is pressed 5 times or more, then the ON/OFF button is pressed, the machine returns to
the service mode menu selection.
Ink absorber counter value to be set (%)
Paper
30 / 43