aevit 2.0 Kurulum Kılavuzu - Sayfa 8

TV Montajı aevit 2.0 için çevrimiçi göz atın veya pdf Kurulum Kılavuzu indirin. aevit 2.0 17 sayfaları. Mounting brackets

Sayfayı Yazdır

prIMArY INpUT

2.4 gENErIC AdjUSTMENT INSTALLATION

dOOr)

Now that the bases are installed, the adjustment section can now be

mounted. Both the Floor Mounting System and the door Mounting

System will come with the same adjustment section. Therefore, this

section pertains to both installs. The adjustment section comes pre-

assembled from EMC; however, Figures 8 & 9 show exactly how they are

assembled in case you need to disassemble or replace a component. The

main components of the Adjustment Section are the Input Device Ar-

ticulating Swivel Bracket and the quick Adjust Upper Pole (Figure 8). The

main components of the Input Device Articulating Swivel Bracket are the

Input Device Swivel Bracket and the Extension Arm (Figure 9).

INPuT DEvIcE ARTIculAT-

INg SwIvEL BRACkET

QuIck ADjusT uPPER POlE

FIGuRE 8 - ADjusTMENT sEcTION AssEMbly

sTEP 1

Insert the Adjustment Section into either the Floor Base

Plate or the Door Base that was installed in sections 2.2

and 2.3. Adjustment Knob 1 may need to be loosened for

the Adjustment Section to fit into the base. When Adjust-

ment Knob 1 is loosened, it pushes down on the threaded

rod located inside of the quick Adjust Upper Pole. This,

in turn, loosens the wedge at the bottom of the quick

Adjust Upper Pole.

sTEP 2

Once the Adjustment Section Assembly is inserted into

the base, it can be adjusted vertically 4". Once it is at the

correct height, tighten Adjustment Knob 1 thoroughly

(Figure 12). Verify that the quick Adjust Upper Pole will

not move under normal operating conditions.

WARNING:

FAILURE TO TIGhTEN ALL ADjUSTMENT KNOBS

COMPLETELy COULD CAUSE AN ACCIDENT RE-

SULTING IN SERIOUS INjURy AND/OR DEATh.

ADjusTMENT kNOb 1

3/8" FlAT WAshER

3/8" ROllER bEARING

3/8" FlAT WAshER

3/8" FENDER WAshER

2" RubbER WAshER

THREADED ROD

FIGuRE 10 - FlOOR sysTEM

(BrkT-AEVIT-FLr & BrkT-AEVIT

3/8"x4" GRADE 8

BOLT

INPuT DEvIcE

SwIvEL BRACkET

3/8" FENDER WAshER

3/8" FlAT WAshER

3/8" ROllER bEARING

3/8" FlAT WAshER

FIGuRE 9 - INPuT DEvIcE ARTIculATING sWIvEl

BRACkET ASSEMBLY

tighten

adjustMent

knoB 1 to lock

Quick adjust

upper pole

in place

FIGuRE 12 - FlOOR sysTEM

AEVIT 2.0 MOUNTING BRACKETS INSTALL MANUAL

2-5

ADjusTMENT sEcTION

FIGuRE 7

2" RubbER

wASHER

ExTENSION

ARM

ADjusTMENT

kNOB 2

FIGuRE 11 - DOOR sysTEM

ADjusTMENT

SECTION

QuIck ADjusT

uPPER POlE