Alinco DJ-191 Kullanım Kılavuzu - Sayfa 7

Alıcı-Verici Alinco DJ-191 için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Alinco DJ-191 18 sayfaları. Cert communications team procedures
Ayrıca Alinco DJ-191 için: Kullanım Kılavuzu (18 sayfalar), Hızlı Referans (3 sayfalar), Hızlı Referans (4 sayfalar)

Sayfayı Yazdır

III

,usnn

'""1

,fJfJ

CALL CHANNEL

,usnn

,...,

,fJU

6-3

Programming

MEMORY MODE

Pressthe

~keyto

display the "M" icon

above the frequency

segment of the LCD.

Pressing the same

key again will bring back the VFO mode

(the "M" icon disappears).

MEMORY SCROLL

Enter the MEMORY MODE, rotate the

Main Tuning Dial.

MEMORY WRITE

1. Enter the MEMORY MODE.

2. Rotate the Main Tuning Dial to select

the desired memory channel to

program.

3. Enter the VFO MODE. Set the fre-

quency, tone and shift accordingly.

4. Press and hold the

key, then press

the

key to store the information

into the memory channel. (Stored

information: Frequency, Offset, Shift

direction, CTCSS setting, CTCSS

frequency, Power H/L, DSQ setting,

DSQ code, Skip, Battery Save setting.)

5. A high tone beep will sound indicating

that the programming is completed

successfully.

6. Memorized items in a channel may

be temporarily changed while you stay

on that channel, but the written infor-

mation remains as originally program-

med. The original items will be called

if you change the memory elsewhere

(or to VFO) then come back to the mem-

ory channel, unless re-programmed

with

and

keys.

MEMORY ERASE

1. Enter the MEMORY MODE.

2. Rotate the Main Tuning Dial to select

the memory channel to erase.

3. Press and hold the

key, then press

the

key to erase the program in-

formation on the memory channel.

4. A high tone beep will sound and the

flashing "M" icon will appear on the

LCD indicating that the memory con-

tent has been erased.

MEMORY SKIP

1. Enter the MEMORY MODE. Rotate

the Main Tuning Dial to the channel

you desire to skip during scanning

operation.

2. Press and hold the

key, then press

the @5\ey.

3. The 'i;equency decimal point will

disappear indicating that the mem-

ory channel will be skipped when

scanning.

4. To cancel the MEMORY SKIP, repeat

these steps.

MEMORY CHANNEL DISPLAY MODE

Instead of displaying a frequency, in

memory mode, the corresponding

memory channel number only may be

displayed. In this mode you cannot

entre VFO and you cannot program or re-

program a memory channel unless you

first exit the Memory Channel Display

Mode. To entre this mode, first program

FL or KL (see Section 8-4 Other Func-

tions), and input through keypad

631 .

The display turns to Channel Number.

(At least one channel has to be already

programmed when you do this, orelse

.. c h -

r "

will appear.) Then cancel

the FL or KL. Where "skip" channels

have been set, the hyphen between'

h "

and the channel number is not displayed.

Repeat the same steps to exit this mode

and get back the frequency display.

Press the

key.

The"

icon will ap-

pear on the top right

of the LCD. Press

~ to come back to

the previous channel.

CALL CHANNEL WRITE

1. Enter the MEMORY MODE.

2. Rotate the Main Tuning Dial to select

the call channel.

3. Enter the VFO MODE. Set the fre-

quency, tone and shift accordingly.

4. Press and hold the

key, then press

the

key to store the information

into the call channel.

5. A high tone beep will sound indicating

that the programming is completed

successfully.

Note: SCAN,

C€5,

<E:)

keys, and the

Main Tuning Dial are not operata-

ble in the CALL CHANNEL mode.

6-4 Scanning

Transceiver has the timer scan function.

In this operation, scan stops at a busy

channel and resumes after 5 seconds.

VFO(BAND) SCAN

Enter the VFO MODE. Press the

@3"

key, and the frequency decimal point will

start blinking to indicate the scanning

mode.

MEMORY SCAN

Enter the MEMORY MODE, and press

the

@3R

key. (Will not start scanning if

the call channel is indicated.)

SCAN DIRECTION

In the SCAN MODE, rotate the Main

Tuning Dial counter-elockwise to scan

downward and clockwise to scan upward.

STOP SCAN

Press the

@3"

key again, or press the

PTT key.

Note: For those memories programmed

with SKIP (see following section),

they will be passed without receiv-

ing while scanning.

SCAN SKIP

Press and hold the

key and press the

@5'

key. Decimal point disappears from

th~

frequency display, and the channel

will be skipped when scanning.