Olympus BH2 Series Komple Söküm, Temizlik ve Yeniden Montaj - Sayfa 2
Mikroskop Olympus BH2 Series için çevrimiçi göz atın veya pdf Komple Söküm, Temizlik ve Yeniden Montaj indirin. Olympus BH2 Series 40 sayfaları. Phase contrast
Ayrıca Olympus BH2 Series için: Sorun Giderme ve Ayarlama Kılavuzu (46 sayfalar), Komple Söküm, Temizlik ve Yeniden Montaj (23 sayfalar), Söküm, Temizlik ve Yeniden Montaj (45 sayfalar), Manuel (6 sayfalar), Kurulum Kılavuzu (9 sayfalar)
Sayfayı Yazdır
Introduction ............................................................................................................................................................................ 7
Scope of this Document ...................................................................................................................................................... 7
A Few Notes Before Starting ................................................................................................................................................... 7
A Caution Regarding Stiff Focus Mechanisms ................................................................................................................. 7
Left-Hand and Right-Hand Side Designations ................................................................................................................. 7
Label Parts for Identification and Reassembly ................................................................................................................ 7
Cleaning Grease from Parts ............................................................................................................................................ 7
Tools Needed .......................................................................................................................................................................... 7
Electric Heat Gun ................................................................................................................................................................ 7
A Few Words about JIS Screws ........................................................................................................................................... 7
Supplies Needed ..................................................................................................................................................................... 8
Recommended Lubricant Types .......................................................................................................................................... 8
Recommended Solvents ..................................................................................................................................................... 8
Solvent Compatibility with Painted Surfaces .................................................................................................................. 8
Solvent Compatibility with Metal Parts .......................................................................................................................... 8
Solvent Compatibility with Plastic Parts ......................................................................................................................... 8
Servicing the Coaxial Focus Assembly ..................................................................................................................................... 8
Remove the Accessories from the Stand ............................................................................................................................ 8
Protect the Exposed Mounting Dovetails ........................................................................................................................... 8
Remove the Lamphouse ..................................................................................................................................................... 9
Remove the Substage Condenser Carrier ........................................................................................................................... 9
Remove the Rear Cover ...................................................................................................................................................... 9
Remove the Focus Gearbox .............................................................................................................................................. 10
Remove the Focus Rack .................................................................................................................................................... 10
Check the Focus Block for Freedom of Motion................................................................................................................. 11
Remove the Fine-Focus Knob Caps ................................................................................................................................... 11
Remove the First Fine-Focus Knob.................................................................................................................................... 12
Remove Second Fine-Focus Knob with Shaft .................................................................................................................... 12
Remove the Fine-Focus Thrust Washers .......................................................................................................................... 13
Remove the Left-Hand Coarse-Focus Knob ...................................................................................................................... 13
Remove Stop Screw for the Pre-Focus Lock Collar ........................................................................................................... 14
Disassemble the Pre-Focus Stop Mechanism ................................................................................................................... 14
Disassemble the Fine-Focus Gear Cluster ......................................................................................................................... 16
Reassemble the Fine-Focus Gear Cluster .......................................................................................................................... 18
Withdraw the Coarse-Focus Shaft .................................................................................................................................... 19
Remove the Pinion Assembly from the Pillar Arm ............................................................................................................ 19
Clear the Adhesive from the Setscrew Heads ................................................................................................................... 19
Remove the Setscrews ...................................................................................................................................................... 20
Service the Sliding Focus Block ......................................................................................................................................... 20
Remove the Tension-Adjustment Knob ............................................................................................................................ 20
Remove the Coarse-Focus Tension Washers .................................................................................................................... 20
Disassemble the Pinion Assembly ..................................................................................................................................... 21
Clean and Reassemble the Pinion Assembly..................................................................................................................... 22
Reinstall the Tension Knob and Washers .......................................................................................................................... 23
Reinstall the Pinion Assembly into the Pillar Arm............................................................................................................. 24
Reinstall the Coarse-Focus Shaft ....................................................................................................................................... 25
Reassemble the Pre-Focus Stop Mechanism .................................................................................................................... 26
Complete Teardown, Cleaning, and Reassembly of the Olympus BH-2 Coaxial Focus Mechanism
Table of Contents
Revision 4
Page 2 of 40