Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Manuel - Sayfa 14

Anahtar Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion için çevrimiçi göz atın veya pdf Manuel indirin. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 19 sayfaları. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Ayrıca Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion için: Kurulum Notu (14 sayfalar), Çözüm Kılavuzu (17 sayfalar), Kurulum Notu (46 sayfalar), Beyaz Kitap (19 sayfalar), Açıklama (1 sayfalar), Ürün Bülteni (6 sayfalar), Uyarı (4 sayfalar), Veri Sayfası (9 sayfalar), Veri Sayfası (18 sayfalar), Beyaz Kitap (18 sayfalar), Yapılandırma Kılavuzu (8 sayfalar), Kurulum Notu (28 sayfalar), Sorun Giderme Kılavuzu (11 sayfalar), Kurulum Notu (18 sayfalar), Kullanıcı Kılavuzu (17 sayfalar), Kurulum Notu (24 sayfalar), Kurulum Notu (36 sayfalar)

Sayfayı Yazdır
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Manuel
Cisco - Connecting a Terminal to the Console Port on Catalyst Switches
Use a null-modem cable to connect the switch to a remote DCE device, such as a modem or a Data
Service Unit (DSU). Use a straight-through cable to connect the switch to a data terminal equipment
(DTE) device, such as a terminal or a PC.
The console port of the Catalyst 4000 Supervisor Engine I uses a DB-25 connector and supports Data
Terminal Ready (DTR), Data Set Ready (DSR), Clear To Send (CTS), and Request To Send (RTS)
handshake signals.
Table G-1
Table G-1: Catalyst 4003 Console Port Pinouts
Pin
Signal
1
Ground
2
RxD
3
TxD
4
CTS
5
RTS
7
Ground
8
DTR
20
DSR
Connecting a Terminal to the Catalyst 4000/4500
Supervisor Engine II/II+/III/IV, 2948G, 2980G, and
4912G
You may configure the Catalyst 4000/4500 series switches from a direct console connection to the
console port.
Use the RJ-45-to-RJ-45 rollover cable and RJ-45-to-DB-9 female data terminal equipment (DTE)
adapter (labeled "Terminal") to connect the console port to a PC running terminal emulation
software. If you are using a direct console connection, configure your terminal emulation program
for 9600 baud, 8 data bits, no parity, and 1 stop bit.
Table H-1
lists the switch console port pinouts. Use a straight-through cable to connect the switch to a
DTE device, such as a terminal or a PC.
Table H-1: Catalyst 4000/4500 Supervisor II and higher, 2948G, 2980G, and 4912G Console Port
http://www.cisco.com/warp/public/473/9.html (14 of 19) [9/4/2003 12:36:03 PM]
lists the Catalyst 4000 Supervisor Engine I console port pinouts.
Direction
Input
Receive Data
Output
Transmit Data
Input
Clear To Send
Output
Request To Send
Output
Data Terminal
Input
Data Set Ready
Description