Epson 835p - PowerLite XGA LCD Projector Ürün Bilgileri - Sayfa 12

Projektör Epson 835p - PowerLite XGA LCD Projector için çevrimiçi göz atın veya pdf Ürün Bilgileri indirin. Epson 835p - PowerLite XGA LCD Projector 21 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson 835p - PowerLite XGA LCD Projector için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Hızlı Kurulum (4 sayfalar), Kullanım Kılavuzu (47 sayfalar), Ürün Destek Bülteni (30 sayfalar), Tamamlayıcı Kılavuz (1 sayfalar), Broşür ve Teknik Özellikler (4 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), Teknik Özet (7 sayfalar), İşlev Kılavuzu (5 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar), Şartname Sayfası (4 sayfalar)

Sayfayı Yazdır

Epson 835p - PowerLite XGA LCD Projector Ürün Bilgileri

Epson PowerLite 835p

Ad Hoc mode

Access Point mode

3. If you've already set up your computer and projector for the

mode you want to use—Ad Hoc mode (also called

computer-to-computer mode) or Access Point mode (also

called infrastructure mode)—skip to "Projecting

Wirelessly" on page 13.

Otherwise, continue with the next section.

Configuring the Connection

Note: Make sure you've installed the NS Connection software.

To connect to the projector over a wireless network, your computer

must be running Windows 98, Me, 2000, or XP. Your

Macintosh must be running OS X 10.2.4 or later. See page 183

for complete system requirements for projecting wirelessly.

Access Point mode (infrastructure mode) is required to achieve

transfer speeds up to 54MB/sec on an 802.11g network. Ad Hoc

mode (computer-to-computer mode) limits network connections to

11MB/sec. This is a standard specification of 802.11g

networking.

Epson PowerLite 835p

You can use NS Connection to connect to the projector and

send images wirelessly in two modes: Ad Hoc mode or Access

Point mode.

Ad Hoc mode (computer-to-computer mode) lets you

connect just one computer to the projector at a time; it's

easy to set up, and the only equipment you need is a

computer with a wireless (802.11g or 802.11b) network

card or adapter, or a Macintosh with an AirPort

AirPort Extreme card.

Access Point mode (infrastructure mode) lets multiple

computers access the projector at the same time and easily

trade off control over the projector. To use Access Point

mode, you need a wireless (802.11g or 802.11b) access

point or an AirPort Extreme (or AirPort) base station, and

one or more computers with wireless network cards or

adapters.

Follow the instructions below for the mode you want to use.

Using Ad Hoc Mode

To use Ad Hoc (computer-to-computer) mode, adjust your

projector and wireless card or adapter settings as described in

this section.

Configuring the Projector

Switch the projector to EasyMP mode and insert the Epson

802.11g card. You see this screen:

4. To select

Config

control. You see the following screen:

10/04

, press the

button on the remote

Enter

Easy connect mode

Config

button