Bosch Professional GWS 800 Оригінальна інструкція з експлуатації - Сторінка 9
Переглянути онлайн або завантажити pdf Оригінальна інструкція з експлуатації для Електроінструмент Bosch Professional GWS 800. Bosch Professional GWS 800 23 сторінки.
Друкувати сторінкуfailure or when the mains plug is pulled. This prevents
uncontrolled restarting.
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for cutting, roughing and brush-
ing metal and stone materials without the use of water.
A separate protective guard for cutting must be used when
cutting with bonded abrasives.
Sufficient dust extraction must be provided when cutting
stone.
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Spindle lock button
(2) On/off switch
(3) Combination wrench for M10 grinding spindle
(4) Auxiliary handle (insulated gripping surface)
(5) Protective guard for grinding
(6) Protective guard for cutting
(7) Locking screw for protective guard
(8) Mounting flange with O‑ring
(9) Grinding disc
a)
(10) Carbide grinding head
a)
(11) Cutting disc
a)
(12) Clamping nut
(13) Grinding spindle
(14) Hand guard
a)
Bosch Power Tools
(15) Rubber sanding pad
(16) Abrasive disc
(17) Round nut
(18) Cup brush
(19) Handle (insulated gripping surface)
(20) Extraction guard for cutting with cutting guides
(21) Diamond cutting disc
a) Accessories shown or described are not included with the
Technical Data
Angle Grinder
Article number
Rated power input
Power output
Rated speed
Max. grinding disc diameter
Grinding spindle thread
Max. thread length of grinding
spindle
Weight according to EPTA-Procedure 01:2014
– with low-vibration auxiliary
– with standard auxiliary
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
Fitting Protective Equipment
u
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
a)
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
a)
a)
a)
a)
a)
a)
product as standard. You can find the complete selection of
accessories in our accessories range.
handle
handle
Pull the plug out of the socket before carrying out any
work on the power tool.
1 609 92A 7C2 | (11.08.2022)
English | 9
a)
GWS 800
3 601 C94 3..
W
800
W
460
min
11,000
–1
mm
100
M 10
mm
17
kg
1.6
kg
1.5
/ II