Aqua One MariSys 240 Посібник - Сторінка 8

Переглянути онлайн або завантажити pdf Посібник для Системи фільтрації води Aqua One MariSys 240. Aqua One MariSys 240 15 сторінок.
Також для Aqua One MariSys 240: Посібник з швидкого налаштування (2 сторінок)

Друкувати сторінку

Set Up Instructions

The aquarium's water level can also be raised

or lowered by adjusting the Water Level

Adjuster. (10) Raising the tube will cause the

aquarium's water level to rise and lowering the

Water Level Adjuster will cause the aquarium's

water level to drop.

3. Remove the pre-filter pad, rinse it under

water and place back into the Overflow Box.

4. Turn the Screw Adjuster (11) located at the

bottom of the Overflow Box to level it.

5. Position the Priming Pump (12) with hanger

next to the Overflow Box on the aquarium's rim.

Connect one end of the airline tubing to the

Priming Pump "in" (13) port (indicated by the

arrow which points towards the Priming Pump

on the red connection adapter). Connect the

other end of the airline tubing to the V-Joint (14)

located at the top of the Water Bridge. (15)

6. Connect the second piece of airline tubing to

the "out" (16) port of the Priming Pump

(indicated by the arrow pointing away from the

Priming Pump on the red connection adapter)

and secure the other end of the airline back into

the aquarium. It is very important to ensure this

hose does not dislodge as it will drain the

aquarium.

7. Measure the distance from the Overflow Box

to the MariSys. Be accurate so you do not cut

the hose too short. (Measure twice and cut

once) Take the utility knife and cut the Large

and Small Flexible Hosing (17) to the desired

length.

The Flexible Hosing must follow a straight path

from the Overflow Box to the MariSys. There

can be a little slack but not too much or the filter

will not operate correctly.

8. Place a Hose Clamp over the end of each

piece of Flexible Hose and slide the Flexible

Hosing over the outlet and inlet, located on the

base of the Overflow Box. Do not tighten the

Hose Clamps yet.

9. Do the same for the connections at the top of

the MariSys.

10. Once every thing is in position tighten the

hose clamps so it is a snug fit. DO NOT OVER

TIGHTEN them as you may crack the plastic.

Setting up the Protein Skimmer

For the following section refer to Diagrams 1 &

2 on pages 5 & 6 of this instruction booklet.

1. Set the Protein Skimmer Air Pump (18) in the

cabinet next to the MariSys or on top of it. It is

recommended that the Air Pump always be

positioned higher than the wooden airstone.

Your MariSys is supplied with a Check Valve,

this ensures water does not back siphon into

the Protein Skimmer Air Pump. This allows you

to place the Air Pump on the base of the cabinet

next to the MariSys.

Please Note: All attachments are inserted into

the Airline during production. Simply attach the

blue adapter to the Protein Skimmer Air Pump

and the other end to the Protein Skimmer

Airline Connector (19). Step 2 can be ignored

during set up and referred if needed at a later

date during maintenance.

2. Connect one end of the airline tubing to the

Protein Skimmer Airline Connector (19) and the

other end to Check Valve (20). Connec the

second piece of airline tubing from the Check

Valve to the Air Control Valve (21), and then the

third from the Air Control Valve to the blue

adapter which fits over the 2 outlets of the

Protein Skimmer Air pump.

3. Connect the Waste Hose (22) to the outlet at

the base of the Protein Skimmer Collection Cup

(23), then place the other end of the tubing into

an empty 1 litre Container. (Not supplied) (24)

4. The height of the wooden airstone has been

preset; the bent portion on the rigid tubing of the

Airline Connector is at the recommended

setting.

To raise or lower the airstone, grasp the rigid

tubing and gently turn left or right while pushing

down or pulling up.

If the airstone is positioned too high in the

Reaction Chamber, (25) the air bubbles will

overflow and fill the Collection Cup. Under

normal conditions, the airstone should be

positioned about 1.5 – 2cm from the bottom of

the Reaction Chamber.