CREE LIGHTING KBL EB WIRELESS Інструкція з монтажу Посібник з монтажу - Сторінка 5

Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Ліхтар CREE LIGHTING KBL EB WIRELESS. CREE LIGHTING KBL EB WIRELESS 9 сторінок. Wireless highbay led luminaire with emergency driver, universal hook and cord or pendant mount with sensor

Друкувати сторінку

Wire Form

PIR Sensor

Motion

Indicator

Red LED

SENSOR INFORMATION

NOTE: For programming of sensor and more

detailed description of sensor visit https://

www.legrand.us/wattstopper/fixtures-

sensors-and-controls/fixture-sensors/fsp-

2x1b.aspx.

INSTALLING SENSOR

NOTE: Ensure that you remove the label on

the unit that says, "Remove This Label Before

Installing Lens". If this label is not removed,

the sensor will not work properly.

STEP 1:

Rotate the wire form up as shown. The

wire form will snap into position to hold the

Sensor horizontal. Confirm that Sensor screw

is tight. See Figure 10.

STEP 2:

Locate the wire form on the sensor and

install onto the luminaire by inserting the

wire form into the (2) tabs under the driver

box. See Figure 11.

STEP 3:

Rotate Sensor as needed to level position or

adjust field of view.

NOTE: The horizontal position is fixed.

SENSOR PROGRAMMING

NOTE: The IR Wireless Programming Tool is

needed for the following steps. The following

settings must match to ensure optimal

performance of the Synapse Environment.

5 of 8

Light Sensor

IR Transmitter

IR Receiver

NOTE: The FSP-2X1B sensor has been

preprogrammed with the optimal settings to

provide the widest range of user flexibility in

the field.

Sensor characteristics can be modified in the

Synapse user interface (recommended) or

by using the IR Wireless Programming Tool.

To reset the FSP-2X1B to the Cree Lighting

preprogrammed settings and ensure optimal

performance of the Synapse Environment.

See Figure 13 for preprogrammed setting

chart

STEP 1:

Select FSP-2X1

STEP 2:

Select New Settings

STEP 3:

Input the following Settings for the Synapse

Environment:

HIGH MODE:

10 Volts

LOW MODE:

0 Volts

TIME DELAY:

30 Sec

CUT OFF:

1 Min

SETPOINT:

Disable

SENSITIVITY:

MAX

RAMP UP:

Disable

FADE DOWN:

Disable

PHOTOCELL:

Disable

Driver Box

Sensor Screw

SETTING

High Mode

Low Mode

Time Delay

Cut Off

Setpoint

Sensitivity

Ramp Up

Fade Down

Photocell

STEP 4:

Select SEND

Follows prompts, if "no response from

device" is displayed see the last page for

troubleshooting.

SENSOR DESCRIPTION

The FSP-2X1 is a motion sensor that controls

lighting levels based on occupancy and

ambient light.

The sensor uses passive infrared (PIR)

sensing technology that reacts to changes

in infrared energy (moving body heat) within

the coverage area. Once the sensor stops

detecting movement and the time delay

elapses, lights will go from high to low

mode and eventually turn off if it is desired.

Sensors must directly "see" motion of a

person or moving object to detect them, so

careful consideration must be given to sensor

luminaire placement and lens selection.

Avoid placing the sensor where obstructions

may block the sensor's line of sight. See

Figure 12.

The FSP-2X1 operates at

120V/230V/240V/277V, no power pack is

required. It is designed to be installed in

indoor and outdoor environments. Once the

device is initially powered up, the

FSP-2X1 will use factory default parameters

to operate. If adjustments are needed, the

programming tool must be used.

Tabs

Wire Form

KBL WIRELES

FSP-201B

10V

30 SECONDS

1 MIN

Disabled

Max

Disabled

LPN00814X0001A0_D