Dodge Tigear-2 Інструкція з експлуатації

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Промислове обладнання Dodge Tigear-2. Dodge Tigear-2 8 сторінок. Accessory kit
Також для Dodge Tigear-2: Інструкція з експлуатації (2 сторінок)

Друкувати сторінку

Dodge Tigear-2 Інструкція з експлуатації

These instructions must be read thoroughly before installation or operation. This instruction manual was accurate at the time of

printing. Please see dodgeindustrial.com for updated instruction manuals.

WARNING: To ensure the drive is not unexpectedly started, turn off and

lock-out or tag power source before proceeding. Failure to observe these

precautions could result in bodily injury.

WARNING: Because of the possible danger to person(s) or property from accidents which may result from the improper use of products, it is

important that correct procedures be followed. Products must be used in accordance with the engineering information specified in the catalog.

Proper installation, maintenance and operation procedures must be observed. The instructions in the instruction manuals must be followed.

Inspections should be made as necessary to assure safe operation under prevailing conditions. Proper guards and other suitable safety devices

or procedures as may be desirable or as may be specified in safety codes should be provided, and are neither provided by Dodge

responsibility of Dodge. This unit and its associated equipment must be installed, adjusted and maintained by qualified personnel who are familiar

with the construction and operation of all equipment in the system and the potential hazards involved. When risk to persons or property may be

involved, a holding device must be an integral part of the driven equipment beyond the speed reducer output shaft.

BOLT-ON BASE KIT

Install the detachable base with the smooth side of the base

facing the mounting surface of the reducer. Install the screws

supplied in the kit and tighten all screws to two-thirds of the

appropriate value listed. Then tighten all screws to the final

torque given.

NOTE: If washers are supplied, it is extremely important to use

them with the screws when attaching the base.

Reducer

Bolt or Screw Size

Size

Tigear-2

Instruction Manual

DETACHABLE BASE (QTY.1)

FLAT WASHER (QTY.4)

ALL SIZES EXCEPT SIZE 40

HEX HEAD

CAP SCREW (QTY.4)

Tightening

Torque

(ft-lb)

1/4-20

5/16-18

3/8-16

7/16-14

5/8-11

130

5/8-11

130

Accessory Kit

WARNING: All products over 25 kg (55 lbs) are noted on the shipping

package. Proper lifting practices are required for these products.

STRAIGHT BORE BUSHING KIT

Loosen the six set screws in the hollow bore shaft and insert

the keyed bushing and supplied key into the side of the hollow

bore shaft that will be closest to the driven equipment. Line up

the clearance hole in the bushing with the set screw. Insert the

straight bore bushing into the hollow bore shaft on the opposite

side of the reducer and line up the two clearance holes in the

bushing with the set screws. Apply anti-seize compound to the

driven shaft and slide the reducer onto the driven shaft. Hand

tighten one of the set screws and then hand tighten a set screw

in the same position on the opposite side of the reducer. This

will take up the clearance between the shaft and reducer to the

same side and reduce wobble. Continue the alternating hand

tightening until all the set screws have been tightened. After all

the set screws have been hand tightened, use a torque wrench to

tighten the set screws to the values in the chart below. The 10-32

set screw over the key should be tightened to 3 ft-lb.

Reducer

Size

nor are the

Tightening

Bolt or Screw Size

1/4-28

5/16-24

Torque

(ft-lb)