Dorman 55101 Manual de instrucciones

Navegue en línea o descargue pdf Manual de instrucciones para Accesorios para automóviles Dorman 55101. Dorman 55101 9 páginas. Choke conversion kit

Imprimir página

INSTRUCTIONS

CHOKE

CONVERSION KIT

55101

BEFORE YOU BEGIN:

• Always wear proper safety

equipment when performing repairs.

• Ensure at your point of purchase

that this part fits your exact

vehicle configuration.

• Reference the appropriate service

manual for your vehicle. If you do

not have a service manual, and do

not have the training or experience

to perform the necessary

procedures correctly, seek the

services of a qualified technician.

NEED HELP?

Please call our Technical Support

team for assistance from our team of

certified automotive experts.

1-866-933-2911

55101_Instructions

Remove air filter from carburetor and determine the

type of automatic choke on the car. There are two

basic types:

Integrated

choke

If automatic choke thermostat is an integral part

of carburetor body and uses a black cap or plastic

or metal disc, it is an integrated choke. Follow the

first set of instructions for integrated choke.

Non-integrated

choke

If a rod connects the carburetor choke shaft to

the thermostat mechanism which is located in

the intake manifold, it is a non-integrated choke.

Follow the second set of instructions

for non-integrated choke.

INTEGRATED CHOKE

INSTALLATION

INSTRUCTIONS

STEP 1:

Remove the black plastic cap or metal disc. If a

heat tube is attached to the choke cap, remove

and discard it. Do not remove if it is attached to

the carburetor body. Save all screws, retainers,

clamps, etc., for use in installing this kit. Make

sure the choke shaft and choke butterfly operate

smoothly. If not, clean with choke cleaner.

Dorman Products, Inc. Corporate Office and Customer Service: 1-800-523-2492.

Disclaimer: It is impossible in these instructions to account for all possible circumstances or situations that you may experience when

attempting to install this product. Please consult with a qualified auto technician before attempting to perform any work you are not qualified to

do. Automobiles can be hazardous to work on; be sure to take all necessary safety precautions. Failure to do so may result in property damage

or personal injury. Certain motor vehicle standards and performance requirements may apply to your motor vehicle (such as Federal Motor

Vehicle Safety Standards by the National Highway Traffic Safety Administration). Be sure that your work is performed in accordance with such

standards and that you do not disable any motor vehicle safety feature.

STEP 2:

Determine which of the two plastic caps included

in this kit best fits your carburetor. Discard the

one you will not need. On some carburetors, the

flanges of the cap fit between the three set pins.

On others, the flanges will fit securely within the

carburetor body.

STEP 3:

Breakaway line

Activator lever

Activator shaft

R-clips

Activator shaft

Choke butterfly

Crimp tight

with pliers (do

not remove)

Choke

tang

Insert the actuator shaft in the new plastic cap,

with the activator lever inside the cap. If you are

using the larger cap, insert the activator shaft

assembly (first illustration) in the cap as shown

in the second illustration and set depth. If you

are using the smaller cap, the activator lever will

have to be shortened at the break-away points

as shown in the first illustration. This is done by

grasping activator lever with pliers above break-

away line and then bending back and forth until

the excess portion breaks away. Do one side at a

time. Set the depth of the activator lever within

the cap so it will catch the choke tang in the

carburetor (third illustration), but not so deep

that the activator will bind on the choke housing.

Once the exact position has been determined,

remove the shaft and install the inside R-clip.

Then place the shaft in position again and install

outer R-clip (second illustration).

PAGE 1 OF 9

Activator

lever