Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Note d'installation - Page 4

Parcourez en ligne ou téléchargez le pdf Note d'installation pour {nom_de_la_catégorie} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 18 pages. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Également pour Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion : Note d'installation (14 pages), Manuel de solution (17 pages), Note d'installation (46 pages), Livre blanc (19 pages), Description (1 pages), Bulletin d'information sur les produits (6 pages), Avis (4 pages), Fiche technique (9 pages), Fiche technique (18 pages), Livre blanc (18 pages), Manuel de configuration (8 pages), Note d'installation (28 pages), Manuel de dépannage (11 pages), Manuel de l'utilisateur (17 pages), Note d'installation (24 pages), Manuel (19 pages), Note d'installation (36 pages)

Required Tools

Blank faceplates and cover panels serve three important functions: they prevent exposure to

Warning

hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)

that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not

operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement

1029

Required Tools

These tools are required to upgrade the supervisor engine DRAM:

•

Refer to the Catalyst 6500 Series Switch Installation Guide for the locations of the ESD connectors on

the Catalyst 6500 series switches.

If upgrading a supervisor engine without an MSFC2 (WS-X6K-SUP1A-PFC or WS-X6K-SUP1A-2GE),

Note

proceed to the

The DRAM DIMMs on the Supervisor Engine 1A with an MSFC (WS-X6K-SUP1A-MSFC) are located

Note

beneath the MSFC. The MSFC is not field replaceable. Re-installing the MSFC could damage your

supervisor engine. To upgrade the DRAM, you must also upgrade the MSFC to an MSFC2. Both

upgrades are available in the MEM-S1-128MB-UPG= upgrade kit.

For information on removing the MSFC, refer to the Catalyst 6500 Series Multilayer Switch Feature

Card 2 Installation Note at this URL:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/cfgnotes/78_10605.htm

Always use an ESD wrist strap when handling modules or coming into contact with internal components.

Caution

Before you remove the supervisor engine, you should first upload the current configuration to a server.

You can recover the configuration by downloading it from the server to the nonvolatile memory of the

supervisor engine. For more information, refer to Chapter 26, "Working with Configuration Files," in the

Catalyst 6500 Series Software Configuration Guide.

The DRAM is located beneath the MSFC2. To upgrade the supervisor engine, you must remove the

MSFC2 from the supervisor engine.

Catalyst 6500 Series Supervisor Engine 1A DRAM Upgrade Installation Note

Antistatic mat or foam pad to support the removed supervisor engine

3/16-inch flat-blade screwdriver for the captive installation screws on the supervisor engine

Number 1 Phillips-head screwdriver for the screws and cap nut that fasten the MSFC2 to the

supervisor engine (if an MSFC2 is installed on the supervisor engine)

Your own ESD-prevention equipment or the disposable grounding wrist strap included with all

upgrade kits, field-replaceable units (FRUs), and spares

"Upgrading the DRAM DIMM" section on page 7

to install the DRAM.

78-14357-02