Astria Fireplaces Rhapsody54 Series Panduan Petunjuk Instalasi - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Petunjuk Instalasi untuk Aksesori Perapian Astria Fireplaces Rhapsody54 Series. Astria Fireplaces Rhapsody54 Series 12 halaman. Linear direct-vent fireplaces accessory kits

Halaman Cetak

INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES

CONNECTION AND ROUTE WIRING FOR OPTIONAL PANEL

BACKLIGHT KIT - SIT PROFLAME II SYSTEM

1. After accessing the control compartment (see Page 3, Figure

6), use a screwdriver or similar object to carefully break the

sealant around the wires, taking care not to nick the wires.

2. Plug in the Multi-wire Harness (provided with the Panel

Backlight Kit) into the SimFlame module port with the red

wires (Figures 8 and 12) and the light wire harness into the

light module harness.

3. Plug in the light wire harness (provided with the Panel

Backlight Kit) into the SimFlame Module port with the black

and white wires.

NOTE: If NOT installing the SimFlame (ﬂ icker) Module,

plug the Multi-Wire Harness directly into the light wire

harness (omitting the components outlined in Figure 8)

4. Route the wiring up through the access opening and slide it

into the slot (Figure 14).

5. Attach the wiring to each lamp assembly as described

below and shown in Figure 17:

f i r e - p a r t s . c o m

a. Route one set of three leads (white/green/black)

through the hole in the front of the bracket.

b. Connect the green wire as shown in Figure 17.

c. Insert the lamp (with green wire attached) into the

bracket until the spring clip is engaged.

d. Attach the white (neutral) and black (hot) wires as

shown in Figure 17.

6. Carefully lay the Panel Backlight lamp assemblies and

wiring on the ﬁ replace ﬂ oor. The lamp assemblies will not

be installed until the back panel is installed (In Step 9,

Figure 18 on Page 6).

Light Wire Harness

Light Module Harness

Figure 12 - Connecting the SIT PF II Module

SimFlame Module

Multi-Wire Harness

Red Wires

PF2 Module

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Install back panel

1. Insert the bottom edge of the back panel into the ﬁ replace

ﬁ rst, then position it in front of the previously installed

reﬂ ector (Figure 13).

NOTE: Lift the back panel over the tabs on the rear ledge of

the ﬁ replace.

2. Align the screw holes in the top and bottom edges of the

back panel with the holes in the ﬁ replace ceiling and rear

ledge. Secure using seven (7) #10-16 x 3/8 hex-head sheet

metal screws provided with the ﬁ rebox panel kit.

Left Side

Panel

Tab

Rear Ledge

Fireplace

Front

Figure 13 - Installing the back panel

Route wiring for optional blower kit

NOTE: Use only original, factory-supplied wiring inside the

ﬁ replace. See the wiring diagrams on Page 11.

1. Route the wiring per the instructions (P/N 750028M).

Route wiring for optional power vent kit

NOTE: Use only original, factory-supplied wiring inside the

ﬁ replace. See the wiring diagrams on Page 11.

1. Route the wiring per instructions (P/N 506022-01).

Determine optional ﬁ rebox panel backlight kit wire

routing method

There are two approved methods for routing the wiring for the

optional ﬁ rebox panel backlight kit.

The preferred method is outlined in the following sections. The

alternate method is included for installations where the ﬁ rebox

rear ledge does not have backlight wire routing holes, and is

described in the Appendix section Route and connect optional

ﬁ rebox panel backlight kit wiring and install lamp assemblies

as shown on Page 6.

1. Determine whether the ﬁ rebox rear ledge has backlight wire

routing holes (Figure 14).

Reﬂ ector

Back Panel