Epson 6110i - PowerLite XGA LCD Projector Panduan Pengguna - Halaman 13

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Perangkat lunak Epson 6110i - PowerLite XGA LCD Projector. Epson 6110i - PowerLite XGA LCD Projector 17 halaman. Release of emp ns connection for windows & mac upgrade from v2.50 to v2.51
Juga untuk Epson 6110i - PowerLite XGA LCD Projector: Panduan Pengguna (42 halaman), Panduan Pengoperasian (36 halaman), Panduan Pengoperasian (47 halaman), Spesifikasi (2 halaman), Panduan Tambahan (1 halaman), Panduan Pengaturan Cepat (7 halaman), Panduan Pengguna (1 halaman), Daftar Bagian (1 halaman), Pernyataan Kesesuaian (4 halaman), Buletin Dukungan Produk (25 halaman), Buletin Dukungan Produk (22 halaman), Buletin Dukungan Produk (28 halaman), Buletin Dukungan Produk (41 halaman), Buletin Dukungan Produk (15 halaman), Buletin Dukungan Produk (22 halaman)

Halaman Cetak

Epson 6110i - PowerLite XGA LCD Projector Panduan Pengguna

Replacing the Air Filter

Replace the air filter (or optional smoke filter) when you see

the

Check or Replace the air filter

prevent proper ventilation and can cause overheating and

damage the projector.

To obtain a replacement air filter or smoke filter, contact your

Epson authorized reseller. To find the nearest reseller, call

800-GO-EPSON (800-463-7766). Or you can purchase

online at www.epsonstore.com (U.S. sales) or www.epson.ca

(Canadian sales).

Follow these steps:

1. Turn off the projector and unplug the power cord.

2. Lift the air filter cover by pulling up the tabs.

3. Remove the filter by pulling it straight out from the center.

4. Insert the new filter with the tabs facing the front of the

projector.

5. Close the air filter cover.

6. Reset the air filter timer as described in the next section.

message. Dust clogs

12/07

Resetting the Air Filter Timer

1. Plug the projector in and turn it on.

2. Press the

button on the remote control, select

from the Reset menu, then press

Air Filter Time

3. When you see the confirmation message, select

press

Enter

4. When you're finished, press

Note: The air filter usage timer shows 0H until you've used the

filter for at least 10 hours.

Replacing the Lamp

Although lamp life results vary depending on environmental

conditions and usage, the projection lamp typically lasts about

3400 hours in high brightness mode or 3900 hours in low

brightness mode. It is time to replace the lamp when:

❏ The projected image gets darker or starts to deteriorate.

❏ The message

Replace the Lamp

when the lamp comes on and the lamp warning light

flashes orange. To maintain projector brightness and image

quality, replace the lamp as soon as possible.

❏ The lamp warning light

out).

Note: Turn off the projector when not in use to prolong the life of

the projection lamp.

You can see how long the lamp has been in use by checking

the

option in the projector's Info menu. (See the

Lamp Hours

User's Guide for more information.)

Contact your Epson authorized reseller for a replacement

lamp and request part number

nearest reseller, call 800-GO-EPSON (800-463-7766). Or

you can purchase online at www.epsonstore.com (U.S. sales)

or www.epson.ca (Canadian sales).

Follow these steps to replace the lamp:

1. Turn off the projector.

2. When the P Power light stops flashing, unplug the power

cord.

Warning: Let the lamp cool fully before replacing it.

In the unlikely event that the lamp has broken, small glass

fragments may be present and should be removed carefully to

avoid injury.

3. Let the projector cool for at least an hour (if it has been on).

The lamp is extremely hot immediately after use.

Epson PowerLite 6110i

Reset

Enter

, then

Yes

to exit the menu system.

appears on the screen and

flashes red (the lamp is burnt

. To find the

V13H010L45