Jandy AquaLink RS 설치 매뉴얼 - 페이지 4

{카테고리_이름} Jandy AquaLink RS에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Jandy AquaLink RS 4 페이지. Battery wireless, portable control panel
Jandy AquaLink RS에 대해서도 마찬가지입니다: 설치 매뉴얼 (8 페이지), 설치 지침 (1 페이지), 설치 지침 (1 페이지)

페이지 인쇄

2. Wireless OneTouch Quick Troubleshooting Guide

2.1. The Wireless AquaLink RS will stop communicating anytime interference (such as from a mi-

cro wave oven or other 2.4GHz devices) prevents a valid signal transmission. When communication is lost

the control panel will lock on "Model Number" until a good link is again achieved, usually within a few

sec onds. If com mu ni ca tion is not reestablished within a few seconds or this happens often, use the

troubleshooting in for ma tion below for suggestions.

Symptom

RS System operation is slow or display is erratic.

Cause

Replace socketed chip in OneTouch printed circuit board with Firmware B09 or newer.

Symptom

LCD screen display stays on "Firmware B11".

Cause

No communication between indoor Control Panel and Power Center J-box.

1. Conﬁ rm dip switch settings on both the Indoor Control Panel Transceiver and Power Center

Transceiver are as follows:

• DIPs 1-7 are set identical

• DIP 8 is ON at Power Center J-box PCB

• DIP 8 is OFF at Control Panel Transceiver PCB

2. At the Power Center J-box Transceiver board, press the SW1 setup button and conﬁ rm that the green

LED ﬂ ashes approximately 10 times. You may need to press SW1 more than one time or turn the

power off and back on to get the LED to ﬂ ash.

3. Repeat Step 2 for the Indoor Desktop Control Panel.

4. Recheck the Indoor Desktop Control Panel for proper performance.

5. If there is no communication yet, check LED's at the Power Center J-box Transceiver PCB:

• Red LED must be lit to indicate power. If red LED is not lit check 4-conductor wire connection

to the red 4-pin terminal bar at the Power Center.

• Amber middle LED must blink continually. If not blinking, transceiver needs to be replaced

with part #8114 or #8241 depending on the manufacture date. If amber LED is blinking at

Power Center J-box Transceiver, go to the Indoor Control Panel.

6. If still no communication, check LED's at the Indoor Control Panel Transceiver PCB.

• At the Indoor Control Panel Transceiver PCB, conﬁ rm that the red LED is on indicating power.

If red LED is not lit, conﬁ rm unit is plugged into wall socket and 4-conductor wires are

connected to the red 4-pin terminal bar on the Indoor Control Panel PCB.

• If green LED is lit, indicates correct data is being received from the Power Center. If green

LED is not lit, there is an obstruction of the RF signal caused by metal barriers.

• Test Indoor Control Panel in close proximity to Power Center. If the unit tests okay, the

placement of one or both transceivers needs to be moved for proper communication.

• If green LED is lit, verify that the middle amber LED is blinking continuously which indicates

data transmission from the Indoor Control Panel to the Power Center.

• Go to the Power Center and verify that the green LED is lit, indicating correct data being

received from the Indoor Control Panel.

• This completes veriﬁ cation of the data transmission loop from the Power Center to the Indoor

Control Panel and back.

7. Wireless Control Panel does not revert to sleep mode after 30 seconds, install OneTouch PCB

ﬁ rmware revision "B11".

Troubleshooting

Jandy

AquaLink