Lexmark C925 빠른 참조 - 페이지 3

{카테고리_이름} Lexmark C925에 대한 빠른 참조을 온라인으로 검색하거나 PDF를 다운로드하세요. Lexmark C925 10 페이지. Setup sheet
Lexmark C925에 대해서도 마찬가지입니다: 관리자 매뉴얼 (20 페이지), 관리자 매뉴얼 (12 페이지), 연결 매뉴얼 (7 페이지), 릴리스 노트 (4 페이지), 관리자 매뉴얼 (13 페이지), 유지 관리 매뉴얼 (15 페이지), 매뉴얼 (14 페이지), 관리자 매뉴얼 (12 페이지), 종이 매뉴얼 (3 페이지), 메뉴 맵 (2 페이지), 이동 매뉴얼 (2 페이지), 소모품 매뉴얼 (2 페이지), 정보 매뉴얼 (1 페이지), 인쇄 결함 매뉴얼 (1 페이지), 설치 (2 페이지), 빠른 참조 (12 페이지), 서비스 교육 (18 페이지)

페이지 인쇄
Lexmark C925 빠른 참조
2
Gently pull the extension until it is fully extended.
3
Flex the sheets of paper or specialty media back and forth to
loosen them. Do not fold or crease them. Straighten the edges on
a level surface.
Paper
Envelopes
Transparencies
Note: Avoid scratching or touching the print side.
4
Load the paper or specialty media. Slide the stack gently into the
multipurpose feeder until it comes to a stop.
Notes:
•
Load A3-, A6-, 11x17, JIS B4-, Statement- and legal-size media
in short-edge orientation.
•
Load A4-, A5-, Exec-, JIS B5- and letter-size media in long-edge
orientation.
•
Load envelopes flap side up in short-edge orientation.
•
Do not exceed the maximum amount of media that the
multipurpose feeder can hold.
•
Load only one size and type of paper at a time.
Long-edge orientation
Short-edge orientation
Warning—Potential Damage: Never use envelopes with
stamps, clasps, snaps, windows, coated linings, or self-stick
adhesives. These envelopes may severely damage the printer.
3
5
Adjust the width guide to lightly touch the edge of the stack. Make
sure the paper or specialty media fits loosely in the multipurpose
feeder, lies flat, and is not bent or wrinkled.
6
From the printer control panel, set the Paper Size and Paper Type
for the multipurpose feeder (MP Feeder Size and MP Feeder Type)
based on the paper or specialty media loaded.

Linking and unlinking trays

Linking trays
Tray linking is useful for large print jobs or for printing multiple copies.
When one linked tray is empty, paper feeds from the next linked tray.
When the Paper Size and Paper Type settings are the same for any
trays, the trays are automatically linked. The Paper Size setting is
automatically sensed according to the position of the paper guides
in each tray except Tray 1 and the multipurpose feeder. The Paper
Size setting for the multipurpose feeder must be set manually from
the Paper Size menu. The Paper Type setting must be set for all trays
from the Paper Type menu. The Paper Type menu and the Paper Size
menu are both available from the Paper Size/Type menu.
Unlinking trays
Note: Trays that do not have the same settings as any other tray are
not linked.
Change one of the following tray settings:
•
Paper Type
Paper Type names describe the paper characteristics. If the name
that best describes your paper is used by linked trays, assign a