Panasonic WVNS954 - NETWORK CAMERA 사용 설명서 - 페이지 7

{카테고리_이름} Panasonic WVNS954 - NETWORK CAMERA에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Panasonic WVNS954 - NETWORK CAMERA 21 페이지. Ip video cameras
Panasonic WVNS954 - NETWORK CAMERA에 대해서도 마찬가지입니다: 사양 (2 페이지), 브로셔 (2 페이지), 참조 (2 페이지), 참조 (2 페이지), 설치 매뉴얼 (31 페이지), 통합 참고 사항 (8 페이지), 사용 설명서 (21 페이지)

페이지 인쇄

Panasonic WVNS954 - NETWORK CAMERA 사용 설명서

Preset map-shot: 8 thumbnail images of the preset

position 1-8 ( Setup Instructions) will be displayed

orderly on a newly displayed window. When a

thumbnail image is clicked, the camera moves to the

respective position and live images will be displayed

on the "Live" page.

Notes:

• Do not operate the browser until all the thumbnail

images are displayed and the camera returns to the

original position (where the camera was when "360°

map-shot" or "Preset map-shot" was carried out).

• When "360 map-shot" is carried out while the cam-

era is moving (panning/tilting), images captured

while panning/tilting may be displayed as the thumb-

nail display. In this case, stop the current operation

and carry out "360 map-shot" again.

• When "Preset map-shot" is carried out with an

unregistered preset position (among preset position

1-8), the thumbnail image of the preset position

before the unregistered preset position will be dis-

played.

In this case, the camera will not move when the

thumbnail image is clicked. (For example, when pre-

set position 3 is unregistered, the thumbnail image

of preset position 2 will be displayed as the thumb-

nail image of preset position 3. The camera will not

move when the thumbnail image of preset position 3

is clicked.)

• The camera will not always returns to the exactly

same position where it was before "360° map-shot"

or "Preset map-shot" was carried out. (It may some-

times be slightly different.)

• The window on which the thumbnail images are dis-

played will close when Clicking the following buttons

that can switch the camera channel or reload

images.

[Live] button, multi-screen buttons, image type but-

tons ([MPEG-4]/[JPEG]), image capture size buttons

([VGA]/QVGA), full screen button, [Setup] button

( pages 5 - 7)

To display the thumbnail images again, carry out

"360° map-shot" or "Preset map-shot" again.

Patrol 1: Performs the registered patrol 1 operation.

Patrol 2: Performs the registered patrol 2 operation.

Patrol 3: Performs the registered patrol 3 operation.

Patrol 4: Performs the registered patrol 4 operation.

!2 Control pad/buttons (*2)

: Left-click on the control pad to adjust

the horizontal/vertical position of the

camera (panning/tilting).

Panning/tilting speed will be faster if a

clicked point gets farther from the cen-

ter point of the control pad.

It is also possible to pan/tilt the camera by dragging the

mouse.

Zoom and focus can be adjusted by right-clicking. When

an upper/lower area of the control pad is right-clicked,

the displayed image will be zoomed in/out on. When a

left/right area is right-clicked, the focus will be adjusted

to the NEAR/FAR side.

Zoom can also be adjusted using the mouse wheel.

!3 BRIGHTNESS buttons (*2)

: The displayed image will be darker.

: The adjusted brightness will return to the

default brightness.

: Image will be brighter.

Note:

When the BRIGHTNESS buttons are clicked while

the camera is at the preset position, the adjusted

brightness will automatically be registered for the

current preset position.

!4 PRESET (*2)

Select a preset position from the pull-down menu

and click the [GO] button. The camera will move to

the selected preset position ( Setup Instructions).

"H" next to the preset position number indicates the

home position. When "Home position" is selected,

the camera will move to the home position.

When the preset ID is registered for a preset posi-

tion, the registered preset ID will be displayed next

to the preset position number.

!5 Camera title

The camera title entered for "Camera title" on the

[Basic] tab will be displayed. ( Setup Instructions)

Alarm occurrence indication button (*2)

This button will be displayed and will blink when an

alarm has occurred. When this button is clicked, the

alarm output terminal will be reset and this button

will disappear. ( Setup Instructions)