Siemens SIPART PS2 설치 지침 - 페이지 4

{카테고리_이름} Siemens SIPART PS2에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Siemens SIPART PS2 4 페이지. Mounting bracket kit
Siemens SIPART PS2에 대해서도 마찬가지입니다: 사용 설명서 (28 페이지), 설치 지침 (4 페이지), 하드웨어 설치 매뉴얼 (30 페이지), 기술 설명 (26 페이지), 간결한 사용 설명서 (35 페이지), 키트 설치 지침 (9 페이지), 설치 지침 (11 페이지)

페이지 인쇄

15900-766

8. Mount the positioner on the manifold:

•

Linkage P – Place an O-ring in the manifold recess. Orient the positioner against the manifold as

shown on page 1 with the feedback pin in the slot in the feedback lever. Insert two M8 x 25

socket head screws with lockwashers into the manifold and thread into the positioner.

•

Linkage U – Place an O-ring in the manifold recess. Orient the positioner against the manifold as

shown on page 1 with the feedback pin in the U-channel. The spring loaded feedback pin should

compress about 1/4". Insert two M8 x 25 socket head screws with lockwashers into the manifold

and thread into the positioner.

9. Tighten all hardware.

10. Read the "Cautions" on page 2 and then apply the appropriate air pressures to fully stroke the valve.

Exercise the positioner/actuator assembly to ensure that:

•

The feedback arm is approximately perpendicular to the valve stem at the mid-stroke

position. Adjust the positioner location as necessary.

•

The feedback linkage does not prevent the valve from fully stroking. Adjust as needed.

•

The feedback pin moves freely within the feedback arm or U-channel for the entire valve

stroke. Adjust the pin position and positioner location as necessary.

•

All hardware is tightened securely.

11. Once the linkage moves freely for the entire stroke, make any additional electrical and pneumatic

connections and then proceed to the calibration instructions in the instrument manuals (see page 1

footnote).

CUSTOMER/PRODUCT SUPPORT

For the location of your local Siemens representative, visit the Siemens Process Instrumentation product

support page at

http://www2.sea.siemens.com/Products/Process-Instrumentation/Support/Customer-

Support.htm.

For technical support refer to the following table and click the appropriate link.

Technical Support

Online Support Request

Telephone

Hours of Operation

Technical Publications

in PDF

Public Internet Site

Repair Service

SIPART is a registered trademark and ValvePAC is a trademark of Siemens Energy & Automation, Inc. Other trademarks are the

property of their respective owners. All product designations may be trademarks or product names of Siemens Energy &

Automation, Inc. or other supplier companies whose use by third parties for their own purposes could violate the rights of the

owners.

Siemens Energy & Automation, Inc. assumes no liability for errors or omissions in this document or for the application and use of

information in this document. The information herein is subject to change without notice.

Procedures in this document have been reviewed for compliance with applicable approval agency requirements and are considered

sound practice. Neither Siemens Energy & Automation, Inc. nor these agencies are responsible for product uses not included in the

approval certification(s) or for repairs or modifications made by the user.

http://www.siemens.com/automation/support-request

1 800 333 7421

8 a.m. to 4:45 p.m. eastern time, Monday through Friday (except

holidays)

http://www2.sea.siemens.com/Products/Process-

Instrumentation/Support/PI-User-Manuals.htm

(e.g. Control Solutions)

http://www2.sea.siemens.com/Products/Process-Instrumentation

1 800 365 8766 extension 3187 (for warranty and non-warranty service)

then click the product line