Cisco 6160 설치 및 교체 참고 사항 - 페이지 12

{카테고리_이름} Cisco 6160에 대한 설치 및 교체 참고 사항을 온라인으로 검색하거나 PDF를 다운로드하세요. Cisco 6160 18 페이지. Without a pots splitter configuration
Cisco 6160에 대해서도 마찬가지입니다: 빠른 참조 매뉴얼 (38 페이지), 하드웨어 설치 매뉴얼 (21 페이지), 설치 절차 매뉴얼 (32 페이지)

페이지 인쇄

Removing and Installing the Cisco 6160 PEM

Power on the PEM by setting the circuit breaker to the ON (1) position, as necessary.

Step 7

Note

Verify that the INPUT OK LED is green.

Step 8

Note

Confirm that the Cisco IOS software recognizes the new PEM.

Step 9

Type the following command:

DSLAM# show hardware chassis

Scroll through the data and locate the PEM information.

The information displayed on the screen will be similar to the following output:

Slot 2 Power Module EEPROM:

Hardware Revision : 1.0

Part Number : 34-1259-01

Deviation Number : 0-0

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Chassis Serial Number : 000000PP830

Power Supply Type : DC

CLEI Code : ABCDEFGHIJ

Asset Identifier :

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 41 01 00 82 22 04 EB 01 80 00 00 00 00 03

0x10: 00 81 00 00 00 00 04 00 C2 8B 30 30 30 30 30 30

0x20: 50 50 38 33 30 0B 01 C6 8A 41 42 43 44 45 46 47

0x30: 48 49 4A CC 20 00 00 00 00 00 00 00 00 00 00 00

0x40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

0x50: 00 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x80: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x90: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0xA0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0xB0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0xC0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0xD0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

Note

Installing a PEM

The OUT FAIL LED might flash briefly.

If the INPUT OK LED is not green or if other issues arise, refer to the Cisco 6160 Hardware

Installation Guide for troubleshooting procedures.

If the information displays as "Unreadable" or "Unknown", the PEM was not installed properly

or a problem exists with the PEM. Install the PEM again by following the procedures in this

section. If the PEM is still not recognized by the system, refer to the Cisco 6160 Hardware

Installation Guide for troubleshooting procedures.

OL-2181-01