Epson TM-L90 series 제조 매뉴얼 - 페이지 9

{카테고리_이름} Epson TM-L90 series에 대한 제조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Epson TM-L90 series 22 페이지. Attaching cover on the power switch
Epson TM-L90 series에 대해서도 마찬가지입니다: 브로셔 (1 페이지), 브로셔 (2 페이지), 제품 설명서 (27 페이지), 사양 (2 페이지), 사양 (8 페이지), 정보 매뉴얼 (5 페이지), 사양 (4 페이지), 사용자 설명서 (40 페이지), 사용자 설명서 (17 페이지), 사용자 설명서 (21 페이지), 사용자 설명서 (21 페이지), 여기에서 시작 (2 페이지), 여기에서 시작 (2 페이지), 매뉴얼 (13 페이지), 사용 설명서 (12 페이지), 사용자 설명서 (36 페이지), 개발 매뉴얼 (34 페이지), 매뉴얼 (2 페이지)

페이지 인쇄
Epson TM-L90 series 제조 매뉴얼
Confidential

3.6 Requirements for Die-Cut Label Size

When manufacturing die-cut label paper (with or without black marks), be sure that the paper
meets the following requirements. (The ESC/POS commands expands the settable range,
omitting the margin settings or the limitation on use (NOTE 2 of Section 3.6).)
Corner R2 or less
L
3
1.5 or more
1.75 ± 0.5
1.5 or more
NOTES: 1. Be sure to set the cutting position (L
2. Since the position of the print head and the cutter is not contiguous, the printer
operates as follows when the paper is cut:
1 Completes printing
2 Feeds the paper to the cutting position
3 Cuts the paper
4 Feeds the next label in reverse to the print starting position
Depending on the paper setting or the paper size, the tip of the next label may be
fed over the print head in action 2 above, or the paper may be fed incorrectly or
jammed by catching the tip of the next label with the print head in 4.
To avoid this, be sure that the distance from the cutting position to the print
starting position (=L
length must be 25.4 mm {1"}.
If (L
3
may be fed wastefully because action 4 is not performed.
37.5 ± 0.5 ~ 69.5 ± 0.5 or 79.5 ± 0.5
(Label length:
L
4
25.4 ~ 101.6)
Cutting position
(Printable area)
2.8 or more
Face stock (printing face)
Label Size Requirement
–L
) is 3.6 mm {0.14"} or more. And the minimum label
3
4
–L
) is less than 3.6 mm or the label length is less than 25.4 mm, the paper
4
TITLE
TM-L90
Roll Paper
Manufacturing Guide
Label interval L1:
30.4 ~ 106.6
1.75 ± 0.5
2.8 or more
) between labels.
4
SHEET
REVISION
A
= 5 ± 0.5
L
2
Paper feeding
direction
[Units: mm]
NO.
NEXT
SHEET
6
5