Olympus BH2 Series Demontage, reiniging en hermontage - Pagina 5
Blader online of download pdf Demontage, reiniging en hermontage voor {categorie_naam} Olympus BH2 Series. Olympus BH2 Series 45 pagina's. Phase contrast
Ook voor Olympus BH2 Series: Handleiding voor probleemoplossing en afstelling (46 pagina's), Volledige demontage, reiniging en hermontage (23 pagina's), Volledige demontage, reiniging en hermontage (40 pagina's), Handmatig (6 pagina's), Installatiehandleiding (9 pagina's)
Pagina afdrukken
Figure 84 - Carefully lift and remove the diaphragm rotor ........................................................................................... 23
Figure 85 - Diaphragm leaves in the metal stator ......................................................................................................... 24
Figure 86 - Carefully remove the diaphragm leaves ..................................................................................................... 24
Figure 87 - Thoroughly clean the diaphragm stator ...................................................................................................... 24
Figure 88 - Thoroughly clean the diaphragm leaves ..................................................................................................... 24
Figure 89 - Thoroughly clean the field diaphragm rotor ............................................................................................... 24
Figure 90 - Features of the field diaphragm leaves ....................................................................................................... 25
Figure 91 - Mark the location of the pivot holes in stator ............................................................................................ 25
Figure 92 - Reinstall first diaphragm leaf into the stator .............................................................................................. 25
Figure 93 - First leaf installed in field diaphragm stator ............................................................................................... 25
Figure 94 - Install the second diaphragm leaf ............................................................................................................... 25
Figure 95 - Continue installing the field diaphragm leaves ........................................................................................... 25
Figure 96 - First seven field diaphragm leaves installed ............................................................................................... 26
Figure 97 - Use index finger to hold the leaves down ................................................................................................... 26
Figure 98 - Lift free end of leaves to slip the next one in .............................................................................................. 26
Figure 99 - Slip seventh leaf under the lifted leaves ..................................................................................................... 26
Figure 100 - Position leaves against the stator side wall .............................................................................................. 26
Figure 101 - Proper orientation of field diaphragm rotor ............................................................................................. 27
Figure 102 - Carefully reinstall the field diaphragm rotor ............................................................................................ 27
Figure 103 - Verify smooth operation of field diaphragm ............................................................................................ 27
Figure 104 - Close field diaphragm to a pinhole aperture ............................................................................................ 27
Figure 105 - Orientation of the screw holes in the rotor .............................................................................................. 27
Figure 106 - Reinstall brass retaining plate onto stator ................................................................................................ 28
Figure 107 - Reinstall screws to secure the retaining plate .......................................................................................... 28
Figure 108 - Reinstall plastic gear collar onto the rotor ................................................................................................ 28
Figure 109 - Secure the gear collar with two screws .................................................................................................... 28
Figure 110 - Reinstall the slotted stop pin into the rotor ............................................................................................. 28
Figure 111 - Ready to be installed into scope (old style) .............................................................................................. 28
Figure 112 - Remove screws securing brass plate to stator .......................................................................................... 29
Figure 113 - Align plastic tab with notch in brass plate ................................................................................................ 29
Figure 114 - Lift and remove the brass retaining plate ................................................................................................. 29
Figure 115 - Lift and remove the plastic rotor from stator ........................................................................................... 29
Figure 116 - Thoroughly clean the plastic rotor ............................................................................................................ 29
Figure 117 - Carefully place the plastic rotor into position ........................................................................................... 30
Figure 118 - Reinstall brass retaining plate onto stator ................................................................................................ 30
Figure 119 - Reinstall screws to secure the retaining plate .......................................................................................... 30
Figure 120 - Plastic stop tab hits tab on retaining plate ............................................................................................... 30
Figure 121 - Ready to be installed into scope (new style) ............................................................................................ 30
Figure 122 - Place field diaphragm assembly into position .......................................................................................... 31
Figure 123 - Secure field diaphragm assembly to base ................................................................................................. 31
Figure 124 - Light Inlet Assembly for the BHT/BHTU .................................................................................................... 31
Figure 125 - Remove setscrews securing barrel to base ............................................................................................... 31
Figure 126 - Remove the Light Inlet Assembly from base ............................................................................................. 31
Figure 127 - Carefully loosen the upper retaining ring ................................................................................................. 32
Figure 128 - Remove the upper retaining ring .............................................................................................................. 32
Figure 129 - Carefully lift and remove adiabatic glass disk ........................................................................................... 32
Figure 130 - Remove the upper spacer tube ................................................................................................................. 32
Figure 131 - Carefully lift and remove frosted glass disk .............................................................................................. 32
Figure 132 - Remove the lower spacer tube ................................................................................................................. 32
Figure 133 - Remove the glass collector lens ................................................................................................................ 33
Figure 134 - The lower retaining ring in the barrel ....................................................................................................... 33
Figure 135 - Loosen the lower retaining ring ................................................................................................................ 33
Figure 136 - Remove the lower retaining ring .............................................................................................................. 33
Teardown, Cleaning, and Reassembly of the Miscellaneous Parts of the Olympus BH-2 Microscope Frames
Revision 1
Page 5 of 45