Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Installatie Opmerking - Pagina 6

Blader online of download pdf Installatie Opmerking voor {categorie_naam} Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 14 pagina's. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Ook voor Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion: Oplossingshandleiding (17 pagina's), Installatie Opmerking (46 pagina's), Witboek (19 pagina's), Beschrijving (1 pagina's), Product Bulletin (6 pagina's), Kennisgeving (4 pagina's), Gegevensblad (9 pagina's), Gegevensblad (18 pagina's), Witboek (18 pagina's), Configuratiehandleiding (8 pagina's), Installatie Opmerking (28 pagina's), Handleiding voor probleemoplossing (11 pagina's), Installatie Opmerking (18 pagina's), Gebruikershandleiding (17 pagina's), Installatie Opmerking (24 pagina's), Handmatig (19 pagina's), Installatie Opmerking (36 pagina's)

Using Flash PC Cards

An MS-DOS formatted ATA Flash PC card or linear Flash PC card can be accessed successfully

Note

(including the dir command) with the Catalyst and Cisco IOS operating systems but will not boot from

ROMMON.

The 16-MB MEM-C6K-FLC16M and 24-MB MEM-C6K-FLC24M linear Flash PC cards are formatted

Note

for the Catalyst 6500 series supervisor engines and are ready to use.

The MEM-C6K-ATA-1-64M and 64-MB MEM-C6K-FLC64M Flash PC cards are not formatted. You

must format these cards (see

the dir disk0: or dir slot0: commands, an unformatted Flash PC card returns a "bad device block info" or

"invalid magic number" error message.

Supervisor Engine 1 and Supervisor Engine 2 do not support the same Flash PC card format. To use a

Note

Flash PC card with Supervisor Engine 2, you must format the card with Supervisor Engine 2. To use a

Flash PC card with Supervisor Engine 1, you must format the card with Supervisor Engine 1.

Table 1 Table 1Table 1Table

Flash devices, including the Flash PC cards. To perform specific tasks, use these commands either alone

or combined with other commands. For example, to copy a file from a TFTP server to a Flash PC card,

set the BOOT environment variable so that the system will boot from this new image and then verify the

boot sequence as shown in the following steps:

The following commands listed in

Note

undelete, squeeze, show flash devices, show flash, and verify.

The ATA Flash PC card is accessed through disk0: and the 16-MB, 24-MB, and 64-MB Flash PC cards

Note

are accessed through slot0:. The following procedure uses slot0:.

Copy a file from a TFTP server to the Flash PC card in slot0:

Step 1

Console (enable) copy tftp slot0:

Set the BOOT environment variable so that the system boots from slot0:

Step 2

Console (enable) set boot system flash slot0:cat6000-sup-5-1-1-CSX.bin prepend

Display the contents of the BOOT environment variable:

Step 3

Console (enable) show boot

For complete descriptions of these commands and how to use them, refer to the Catalyst 6500 Series

Software Configuration Guide and the Catalyst 6500 Series Command Reference publication.

Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note

Table 1 on page 7

for a description of the format command.) When you enter

1shows many of the commands that are available for using and managing

Table 1

are not applicable to the ATA Flash (disk0:) PC card:

78-6507-06