HP 234664-002 - ProLiant - ML330T02 Przegląd - Strona 5

Przeglądaj online lub pobierz pdf Przegląd dla Pulpit HP 234664-002 - ProLiant - ML330T02. HP 234664-002 - ProLiant - ML330T02 20 stron. Visualization and acceleration in hp proliant servers
Również dla HP 234664-002 - ProLiant - ML330T02: Często zadawane pytania (4 strony), Podręcznik wdrażania (35 strony), Biała księga techniczna (12 strony), Aktualizacja oprogramowania sprzętowego (9 strony), Podręcznik wdrażania (26 strony), Wprowadzenie Podręcznik (22 strony), Instrukcja rozwiązywania problemów (18 strony), Podręcznik wdrażania (11 strony), Instrukcja instalacji (2 strony), Podręcznik konfiguracji (2 strony), Wprowadzenie Podręcznik (19 strony), Aktualizacja instrukcji (9 strony), Aktualizacja instrukcji (16 strony), Wprowadzenie Podręcznik (10 strony), Instrukcja instalacji (15 strony), Krótki opis technologii (9 strony)

Figure 3. Representation of a bus clock signal

Over the years, some computer components have gained in speed more than others have. For this

reason, the components in a typical server are controlled by different clocks that run at different, but

related, speeds. These clocks are created by using various clock multiplier and divider circuits to

generate multiple signals based on the main system bus clock. For example, if the main system bus

operates at 100 MHz, a divider circuit can generate a PCI bus frequency of 33 MHz (system clock ÷

3) and a multiplier circuit can generate a processor frequency of 400 MHz (system clock x 4).

Computer components that operate in whole multiples of the system clock are termed synchronous

because they are "in sync" with the system clock.

Synchronous components operate more efficiently than components that are not synchronized

(asynchronous) with the system bus clock. With asynchronous components, either the rest of the

system or the component itself must wait one or more additional clock cycles for data or instructions

due to clock resynchronization. In contrast, synchronized components know on which clock cycle data

will be available, thus eliminating these timing delays.

Memory bus speed

The speed of the DRAM is not the same as the true speed (or frequency) of the overall memory

subsystem. The memory subsystem operates at the memory bus speed, which may not be the same

frequency (in MHz) as the main system bus clock. The two main factors that control the speed of the

memory subsystem are the memory timing and the maximum DRAM speed.

The original DRAM took approximately six system bus clock cycles for each memory access. During

memory access, the RAS and CAS were sent first and then 64 bits of data were transferred through

the memory bus. The next sequential address access required a repeat of the RAS-CAS-Data

sequence. As a result, most of the overhead occurred while transferring row and column addresses,

rather than the data.

FPM and EDO improved performance by automatically retrieving data from sequential memory

locations on the assumption that they too will be requested. Using this process called burst mode

access, four consecutive 64-bit sections of memory are accessed, one after the other, based on the

address of the first section. So instead of taking six clock cycles to access each of the last three 64-bit

sections, it may take from one to three clock cycles each (see Figure 4).

Burst mode access timing is normally stated in the format "x-y-y-y" where "x" represents the number of

clock cycles to read/write the first 64 bits and "y" represents the number of clock cycles required for

the second, third, and fourth reads/writes. For example, prior to burst mode access, DRAM took up to

24 clock cycles (6-6-6-6) to access four 64-bit memory sections. With burst mode access, three