Green R/C Model Airplanes Tiger Moth Kullanım Kılavuzu - Sayfa 7

Oyuncak Green R/C Model Airplanes Tiger Moth için çevrimiçi göz atın veya pdf Kullanım Kılavuzu indirin. Green R/C Model Airplanes Tiger Moth 11 sayfaları. The unique almost-ready-to-fly scale 1:7 model of great britain's famous wwii training aircraft
Ayrıca Green R/C Model Airplanes Tiger Moth için: Kullanım Kılavuzu (11 sayfalar)

Sayfayı Yazdır

Green R/C Model Airplanes Tiger Moth Kullanım Kılavuzu

5) Tighten the two mounting

gear and wheel in place at the bottom of the fuselage end. Be sure that the tail gear can rotate

freely in the mounting plate.

6) Finally, connect the pull-pull control cables to the horns on the elevator and the rudder

respectiv-ly. Adjust the tension in the cables by turning the clevises clockwise or

counter-clockwise on the threaded connector.

Step

Step 5. 5. 5. 5. Installation

Step

Installation of of of of the

Installation

* * * * Open

Bag

Bag 5# 5# 5# 5#

Bag

*Open

Bag

Bag 13#

1) Mount the aileron control horns and aileron pushrods on the ailerons.

pre-drilled to locate the position of the horns.

2) Refer to Fig. (5), locate and remove the aileron servo access doors. Mount your aileron servos to

the access doors. Long servo horns are needed to get the pushrods outside the slots in the servo

door. You will need two servo extensions and one "Y" connector. The wing panels have pull

strings pre-installed. Tie the pull string to your aileron servo wire extensions and carefully pull

the extensions through the wing panels to the exit holes near the center. Connect your extensions

with the "Y" connector.

3) Connect the aileron pushrods to the aileron servo arms.

4) After installing the servos and connecting the servo extensions, re-install the access doors.

Step

Step 6. 6. 6. 6. Assembling

Assembling

Step

Assembling

Assembling the

*Open

Bag

Bag 6# 6# 6# 6#

Bag

*Open

Bag

Bag 7# 7# 7# 7#

Insert the lower wing front

section of the lower wing panel and join the left and right panels tightly together to get the

complete

complete lower

lower

lower wing.

lower

Refer to Fig (6), firstly use the self-tapping screws (W13) to mount the aluminum angle mounts

screws (L10) to secure the mounting plate (L09) along with the tail

the

the aileron

the

aileron

aileron servos

aileron

servos

to get the lower

lower

lower wing

wing

wing panels

aileron

to get the aileron

aileron control

13#

Fig.

Fig. (5)

(5)

(5) Installing

1. Aileron

5. Access door

the

lower

wing

and

and m m m m o o o o unting

the

the lower

lower

lower wing

wing

wing and

and

wing

dihedral

to get the wing

wing dihedral

dihedral joiners

and

to get all the hardware needed for assembling the wings.

Bag

Bag 8# 8# 8# 8#

Bag

front

dihedral

front dihedral

dihedral joiner

wing.

panels

panels with

with

with ailerons

ailerons

ailerons (W03).

control

horns

control horns

horns (C06) and pushrods

Installing

Installing the

the aileron

the

aileron

aileron servos

servos

servos and

servos

2. Aileron horn

3. Pushrod.

6. Long servo arm (not included in kit)

unting

the

wing

unting the

unting

the

the wing

wing struts

wing

joiners

wing

joiners , the wing

wing struts

joiner

joiner (W04) and rear

pushrods

pushrods (C07) . . . .

and

and controls

controls

4. Aileron servo

struts

wing

struts and the wing

wing cabanes.

rear

dihedral

joiner

rear dihedral

dihedral joiner

joiner (W06) into the root

There are holes

cabanes.