Canon PIXMA MP620 series 서비스 매뉴얼 - 페이지 15

{카테고리_이름} Canon PIXMA MP620 series에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon PIXMA MP620 series 46 페이지. Installing your multifunction on additional computers windows os
Canon PIXMA MP620 series에 대해서도 마찬가지입니다: 설정 (4 페이지), 보충 설명서 (6 페이지), 설정 지침 (4 페이지), 매뉴얼 (20 페이지), 사양 (2 페이지), 매뉴얼 (10 페이지), 매뉴얼 (8 페이지), 네트워크 설정 매뉴얼 (22 페이지), 설치 매뉴얼 (11 페이지), 연결 매뉴얼 (19 페이지), 설치 매뉴얼 (7 페이지), 설치 (21 페이지)

페이지 인쇄
Canon PIXMA MP620 series 서비스 매뉴얼
MP620 / MP628

3. REPAIR

3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)
Service part
Logic board ass'y
Absorber kit
Carriage unit
Switch system unit
Paper feed motor
Platen unit
Notes on replacement
- Before removal of the logic board
ass'y, remove the power cord,
and allow for approx. 1 minute
(for discharge of capacitor's
accumulated charges), to prevent
damages to the logic board ass'y.
- Before replacement, check the
ink absorber counter value (by
service test print or EEPROM
information print).
- The red screws securing the paper
feed motor are allowed to be
loosened only for paper feed
motor replacement. (DO NOT
loosen them in any other cases.)
*1
Adjustment / settings
After replacement:
1. Initialize the EEPROM.
2. Set the ink absorber counter
value.
3. Set the destination in the
EEPROM.
4. Check the ink system function.
5. Perform LF / Eject correction.
6. Perform button and LCD test.
Perform 1 to 6 in the service
mode.
[See
3-3. Adjustment /
Settings, (6) Service
details.]
7. Perform print head alignment
and LCD language setting in
the user mode.
8. Reset the LAN settings in the
user mode.
After replacement:
1. Reset the ink absorber counter.
[See
3-3. Adjustment /
Settings, (6) Service
details.]
At replacement:
1. Before removal of the carriage
rail, mark the carriage rail
position.
[See
3-2. Special Notes on
Repair Servicing, (7) Carriage
unit
removal, for details.]
2. Apply grease to the sliding
portions of the carriage rail.
[See
3-3. Adjustment /
Settings, (3) Grease
application, for details.]
3. Check the ink system function.
[See
3-3. Adjustment /
Settings, (6) Service
details.]
4. Perform print head alignment in
the user mode.
At replacement:
1. Adjust the paper feed motor.
[See
3-3. Adjustment /
Settings, (1) Paper feed motor
adjustment, for details.]
After replacement:
1. Perform LF / Eject correction in
the service mode.
[See
3-3. Adjustment /
Settings, (6) Service
details.]
13 / 44
TABLE OF CONTENTS
Operation check
- EEPROM information print
- Service test print
- Printing via USB connection
- Copying
- Direct printing from a digital
camera (PictBridge)
mode, for
- Ink absorber counter value
print (After the ink absorber
counter is reset, the counter
mode, for
value is printed
automatically.)
- Service test print (Confirm ink
system function.)
mode, for
- EEPROM information print
- Service test print
- EEPROM information print
- Service test print
mode, for