Canon PIXMA MX700 Series 서비스 매뉴얼 - 페이지 8

{카테고리_이름} Canon PIXMA MX700 Series에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon PIXMA MX700 Series 44 페이지. Office all-in-one printer
Canon PIXMA MX700 Series에 대해서도 마찬가지입니다: 청소 매뉴얼 (7 페이지), 네트워크 설정 매뉴얼 (32 페이지), 보충 설명서 (6 페이지), 설정 지침 (2 페이지), 브로셔 및 사양 (2 페이지), 기술 정보 (2 페이지)

페이지 인쇄

5 times

ASF (cam) sensor error

6 times

Internal temperature

error

7 times

Ink absorber full

8 times

Print head temperature

rise error

9 times

EEPROM error

10 times

VH monitor error

12 times

APP position error

14 times

APP sensor error

15 times

USB Host VBUS

overcurrent

19 times

Ink tank position sensor

error

22 times

Scanner home position

error

Power and

ROM / RAM error

Alarm LEDs lit

Before replacement of the logic board ass'y, check the ink absorber counter value (by service test print or

EEPROM information print). If the counter value is 7% or more, also replace the ink absorber kit (QY5-0192)

when replacing the logic board ass'y. If the counter value is less than 7%, register the current ink absorber

counter value to the replaced new logic board instead.

[See 3-3. Adjustment / Settings, (10) Service mode, for details.]

[5700] An error occurred in the ASF cam

sensor.

[5400] The internal temperature is not normal.

[5B00,

The ink absorber is supposed to be full.

5B10,

Message on the LCD:

5B01,

Ink absorber full. Service required.

5B11]

Error codes:

Overseas:

5B00: Main ink absorber

5B10: Borderless-print ink absorber

Japan:

5B01: Main ink absorber

5B11: Borderless-print ink absorber

[5200] The print head temperature exceeded the

specified value.

[6800] A problem occurred in writing to the

EEPROM.

[B200] The internal temperature exceeded the

specified value.

[6A80] An error occurred in the APP motor

during purging operation.

[6A90] An error occurred in the APP cam

sensor.

[9000] The USB Host VBUS is overloaded.

[6502] None of the ink tank position is detected. - Spur base unit (QM3-2664)

[5010] The scanner unit cannot detect the home

position, or the scanner unit warming-up

is not performed properly at power-on.

On the LCD, "Scanner is not operating

correctly." is displayed.

---

The check sum value is incorrect in the

ROM check or RAM check at hard-

power-on.

6 / 41

- Logic board (QM3-2834)

- Sheet feed unit (QM3-2677)

- PE sensor board (QM3-2571)

- Logic board (QM3-2834)

- Carriage unit (QM3-2650)

- Ink absorber kit (QY5-0192)

- Print head (QY6-0070)

- Logic board (QM3-2834)

- Print head (QY6-0070)

- Carriage unit (QM3-2650)

- Logic board (QM3-2834)

- Sheet feed unit (QM3-2677)

- Purge unit (QM3-2651)

- Logic board (QM3-2834)

- Sheet feed unit (QM3-2677)

- Logic board (QM3-2834)

- Scanner unit (QM3-2672)

- Logic board (QM3-2834)