DSC Power 832 설치 매뉴얼 - 페이지 7

{카테고리_이름} DSC Power 832에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC Power 832 17 페이지. Central station talk / listen module
DSC Power 832에 대해서도 마찬가지입니다: 사용 설명서 (11 페이지), 사용 설명서 (18 페이지), 사용자 지침 (2 페이지), 설치 지침 매뉴얼 (12 페이지), 사용자 설명서 (20 페이지), 설치 지침 (2 페이지), 설치 지침 (2 페이지)

페이지 인쇄

1. How to Program

Module Operation and Programming

4.1 Module Zone Group Assignment

In order to use the zone expansion portion of the module, you must

select which system zones the expander will occupy.

Subsection [00] Module Zone Group Assignment will accept two

digits. The first corresponds to zone terminals 1-4 on the module

(Group A). The second digit corresponds to zone terminals 5-8

(Group B). Select which system zones these two groups will occupy

by entering the corresponding digit:

0 = Group Not Used

1 = Group Not Used

2 = Zones 9-12

3 = Zones 13-16

For example, to have Group A (Z1-Z4) occupy system zones 9-12,

and Group B (Z5-Z8) occupy zones 13-16, enter [23].

If using Downlook as well as zone expansion, consider the following:

Using zones connected to the PC5108L for Downlook triggering

means that images will be taken 25ms after an event has occurred.

See Section 4.2 "Downlook Operation (DLM-4L)" for more information.

Fire zones should not be used onPC5108L zones.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

Module Zone Group Assignment ................................ Subsection [00]

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

4.2 Downlook Operation (DLM-4L)

When Downlook is initiated, the DLM-4L will store up to four images

from the programmed camera(s). Once the images are stored, the

Downlook module will seize the telephone line to transmit the images

to the central station. The images will be sent after the panel has

communicated the event.

When a Downlook module is connected to the PC5108L, the DLM-4L

Is Connected option must be enabled. In addition, the Local Mode

Enabled/Disabled option (PC5015 panel section [381] option [8])

should be OFF (default setting) if there is a DLM-4L present. If there is

no DLM-4L present on the system, this option should be ON.

Downlook can be initiated according to the following methods:

• Event-initiated Downlook

• Pre-trigger

• Remote trigger

All methods require similar programming. For each event/trigger, both

the Timing and Camera numbers for the transmissions must be

programmed.

The 2-digit Timing entry is the "dwell" time between pictures. That is,

when a camera is selected the picture is taken immediately and then

the PC5108L will freeze on that camera for the length of time specified

in the Timing entry. The value for this entry refers to 100's of ms. The 2-

digt Camera entry corresponds to the camera that will take the image.

4 = Zones 17-20

5 = Zones 21-24

6 = Zones 25-28

7 = Zones 29-32