DSC Power 832 설치 매뉴얼 - 페이지 9

{카테고리_이름} DSC Power 832에 대한 설치 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DSC Power 832 17 페이지. Central station talk / listen module
DSC Power 832에 대해서도 마찬가지입니다: 사용 설명서 (11 페이지), 사용 설명서 (18 페이지), 사용자 지침 (2 페이지), 설치 지침 매뉴얼 (12 페이지), 사용자 설명서 (20 페이지), 설치 지침 (2 페이지), 설치 지침 (2 페이지)

페이지 인쇄

1. How to Program

M O D U L E

Pre-trigger

The pre-trigger section can be programmed to allow Downlook to

activate while the system is idle. This will allow pictures to be taken

constantly while the system is idle.

The DLM-4L will continually follow the programmed pattern until a

Downlook-initiating event occurs. At this point, the pre-trigger se-

quence will be suspended until the appropriate transmissions for the

Downlook-initiating events have been sent.

Do not program video switching features when using Pre-Trigger.

Remote Trigger (for Escort5580 v2.0 or greater)

The remote trigger can only be used for systems that have an

Escort5580 Audio Assistant installed.

With remote trigger, the end user can initiate Downlook to verify the

status of the premises while they are absent. When the remote trigger

is activated, the panel will transmit a System Test reporting code. The

programmed timing and camera settings will then elapse and the

images will be transmitted to central station. The user can then call

the central station to verify the sent images.

Two areas must be programmed for the remote trigger feature:

1. The Timing and Camera entries in Subsection [41] Remote

Trigger

2. The access code must have the following attributes enabled:

Enable EITHER Attribute 5: Remote Trigger Phone 1

For Attribute 5, the Downlook images will be sent to telephone

number 1. For Attribute 6, the Downlook images will be sent to

telephone number 2. Do not enable both attributes on a single

access code.

To initiate Downlook via remote trigger, the user must perform the

following:

1. Access the Escort5580 remotely.

2. Enter [*][8] followed by a valid access code.

If an access code with the correct attributes has been entered, the

Escort5580 will announce "Goodbye" and will terminate the call. The

panel will proceed to collect the Downlook images and transmit them

to the central station.

For more information on the Escort module, see the Escort5580

Installation and Instruction Manuals. For information on programming

access codes, see the PC5015 Instruction Manual.

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

DLM-4L Is Connected ................................ Subsection [50] Option [8]

Pictures Can Be Overwritten ..................... Subsection [50] Option [7]

Event-initiated Downlook .................................. Subsections [01]-[39]

Pre-trigger ................................................................... Subsection [40]

Remote trigger ............................................................ Subsection [41]

○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○

O P E R A T I O N

Enable Attribute 4: Escort access

OR Attribute 6: Remote Trigger Phone 2

A N D

P R O G R A M M I N G